Jump to content
SAU Community

Recommended Posts

it would struggle to make power due to lower compression you would also need exhaust manifolds and non turbo ECU

are you already on your P's, and whats the rule going to say if you have said car registered in your name before the rule comes in

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074383
Share on other sites

hey guys,

i was just wondering if it would be posible to take a turbo skyline (R32 or R33) and take the turbo off while on my ps because of the new p plate laws coming for south australia and put it back on after im off my ps ?? or would there be engine mods needed or wateva? Thanks.

ummm no.!

you will lose way to much power different compression ratios between turbo/non turbo models.

get a different car put the line in the shed until ur off ya P plates or just buy a non turbo car if ur that worried.

regards

Allan.M

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074386
Share on other sites

if the law does come in, then selling a non turbo skyline down the track will be easier than selling one now without those laws :D

hahah Allan

non turbo R34 are very cheap from japan

EDIt

if your choice is only 32 or 33 get the 33 with a RB25de as the 20 would have even less guts again

R33 = RB25

R32 = RB20

GTS = DE

GTSt = DET

R33 GTS4 = RB25DE

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074408
Share on other sites

if the law does come in, then selling a non turbo skyline down the track will be easier than selling one now without those laws :D

hahah Allan

non turbo R34 are very cheap from japan

EDIt

if your choice is only 32 or 33 get the 33 with a RB25de as the 20 would have even less guts again

R33 = RB25

R32 = RB20

GTS = DE

GTSt = DET

R33 GTS4 = RB25DE

You missed a few out

R32 - RB25DE Seen a few of these getting around

And the very rare R32 - RB26DE but I doubt you'd ever find one.

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074446
Share on other sites

a little more info :D

didnt know you could get a CA18 in a R32, and looks like all the 25's were double cams only a couple 20 single cams

The R32 range:

GXi - The bare basic model R32 1.8 litre, rwd, non-turbo, no extras.

GTE - 2 litre family model, four door, non turbo, single overhead cam.

GTS - 2 ltr, in-line 6. DOHC, EFI, 2 & 4 drs, RWD, standard sports model.

GTS25 - 2.5ltr, in-line 6. DOHC, EFI, 2 & 4 drs, RWD, non-turbo, sports model.

GTSt - 2 ltr, in-line 6 cyl, DOHC, EFI, 2 & 4 drs, RWD, turbo charged sports car.

GTS4 - 2 ltr, in-line 6 cyl, DOHC, EFI, 2 & 4 drs, 4WD, turbo - some feature GTR specs (eg ATTESSA 4WD)

GTR - 2.6ltr, in-line 6 cyl DOHC, EFI, 2 dr, twin turbo, 4WS, 4WD, ABS, HICAS...

Basic R32 Specification Chart:

Model Engine Type Description Power Output CC Drive Doors GXi CA18i 1.8litre 4cyl 91PS/5200rpm 1809 RWD 4 door

GTE RB20E 2ltr, 6 cyl, single cam 97kw@5600rpm 172Nm@4400rpm 1998 RWD 4 door

GTS RB20DE 2ltr, 6 cyl, double overhead cam 116kw@6400rpm 184Nm@5200rpm 1998 RWD 2 & 4 dr

GTS25 RB25DE 2.5ltr, 6 cyl, DOHC 142kw@6400rpm 231Nm@4800rpm 2498 RWD 2 & 4 dr

GTSt RB20DET 2ltr, 6cyl, dohc, turbo 160kw@6400rpm 263Nm@3200rpm 1998 RWD 2 & 4 dr

GTS4 RB20DET 2ltr, 6cyl, dohc, turbo 160kw@6400rpm 263Nm@3200rpm 1998 4WD 2 & 4 dr

GTR RB26DETT 2.6ltr, 6cyl, twin turbo 208kw@6800rpm 368Nm@4400rpm 2568 4WD 2 dr

Decifering the Engine name:

RB - series of engine 20 / 25 / 26 - capacity (20~1998cc / 25~2497cc / 26~2597cc) D - Double Overhead Cam (or DOHC) E - EFI (Electronic fuel injection) T /TT - Turbo / twin turbo

Engine Type:

The R32 generally featured the RB series of engine in all instances except for in the case of the R32 GXi which feature the CA18i engine. This was a four cylinder, 1.8 litre normally aspirated engine.

Special models:

During and after general production, a handful of special models were released in small numbers. These rare cars generally featured a small variation from the normal, and seemed to be more like test models than anything. The Autech R32 is an example of this. The Autech R32 was tuned by Autech and was basically a four door R32 GTR, without the turbos, as it housed an RB26DE in its engine bay and an automatic gearbox. You can deduce from the name that the engine was a 2.6 litre DOHC EFI in-line six normally aspirated variant. Very good for pulling trailers since they have tonnes of torque.

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074486
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
    • I haven’t yet cut the chassis, maybe I switch to a reverse flow. I’ve got the Intercooler mounted as I already had it but not cut yet. Might have to speak to an engineer 
×
×
  • Create New...