Jump to content
SAU Community

Recommended Posts

Some f**king assholes broke into my R33 last night.

They didn't take anything because well.. I had nothing in there lol.

I also removed the negative terminal on the battery since I hardly drive it.

They pried open the drivers side window since they are pillarless and shoved their hand in to pull the unlock switch.

Now my windows f**ked cause it's out of place and when I try to open and close it by using the window switch, there's a loud clunk.

Anyone know how to open up the R33 drivers side door and get to the window unit?

Link to comment
https://www.sau.com.au/forums/topic/307613-fking-theives/
Share on other sites

Thats bad luck mate. To remove the trim take off the cap thats inside your hand well on the door then remove screw. lift up the switch panel and unplug. remove all the screws along the bottom of door then pull trim away again at bottom of door a little bit then tap up which should part the top of the trim along the window edge. Remove the plastic carefully and you should then see the window mechanism. you will need to put plastic back on after

Link to comment
https://www.sau.com.au/forums/topic/307613-fking-theives/#findComment-5080337
Share on other sites

Thats bad luck mate. To remove the trim take off the cap thats inside your hand well on the door then remove screw. lift up the switch panel and unplug. remove all the screws along the bottom of door then pull trim away again at bottom of door a little bit then tap up which should part the top of the trim along the window edge. Remove the plastic carefully and you should then see the window mechanism. you will need to put plastic back on after

Thanks for the help mate but I don't know how to lift up the switch panel. I already removed that screw in the hand well but the switch panel will not budge.

Do I also have to remove the door handle card because I'm finding it extremely difficult to undo the door handle clip.

Link to comment
https://www.sau.com.au/forums/topic/307613-fking-theives/#findComment-5080432
Share on other sites

looks like you leave the switch plate attached to the card you disconnect it from behind once you undo card from door. to get the door opener surround off just put your fingers behind one of the corners and pull on it its cliped in. give that a try

Link to comment
https://www.sau.com.au/forums/topic/307613-fking-theives/#findComment-5080514
Share on other sites

looks like you leave the switch plate attached to the card you disconnect it from behind once you undo card from door. to get the door opener surround off just put your fingers behind one of the corners and pull on it its cliped in. give that a try

I can't undo the card from the door because the switch plate is connected to something behind the card and my hand is too big to detach the connection :)

Link to comment
https://www.sau.com.au/forums/topic/307613-fking-theives/#findComment-5080616
Share on other sites

I just pulled my switch plate off, after the screw is out I put my arm along rest with my hand going over end of switch plate. I curled my fingers around and underneath the edge up the top of the switches and pulled up then the switch plate came out. it would only come off with leverage from the top. there is a clip between the hand hole and switches underneath the panel holding it to the door.

Link to comment
https://www.sau.com.au/forums/topic/307613-fking-theives/#findComment-5080880
Share on other sites

I just pulled my switch plate off, after the screw is out I put my arm along rest with my hand going over end of switch plate. I curled my fingers around and underneath the edge up the top of the switches and pulled up then the switch plate came out. it would only come off with leverage from the top. there is a clip between the hand hole and switches underneath the panel holding it to the door.

Thanks I removed the switch plate.

After I remove the plastic thing that covers the door, do I have to remove the steal frame behind it?

Link to comment
https://www.sau.com.au/forums/topic/307613-fking-theives/#findComment-5081159
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...