Jump to content
SAU Community

Recommended Posts

HI GUYS

my r33 gtst auto is playing up and has almost caused a car too smash into me.

if im accelarating and then take my foot off- the idle drops really low sort of bounces a bit of 500 rpm then just engine turns off??and also happens when i put my foot down nail it then slow down??

has this happened too anyone else?

anyone know how too fix it?

or could anyone fix it for my?? i will pay them!!

cheers

Link to comment
https://www.sau.com.au/forums/topic/307997-help/
Share on other sites

O2 sensor is a sensor in your dump pipe that measures air fuel mixtures tell ur ECU if the cars to rich or too lean and then the ecu will balance the car to run appropriately to many definitions google it but thats what it does in a nutshell .... simply purchase one around 70 - 80 bux new... but i suggest you take it to ur local shop to plug it up to their pc to see for fault codes..

Link to comment
https://www.sau.com.au/forums/topic/307997-help/#findComment-5084995
Share on other sites

listen we need more info could be anything at this point mate....

- Does the car turn off if u start it and dont touch it....

give us as much info as you can... !!!

ye but when i start it-it doesnt really start unless i rev it.

pretty much i drive take foot off the gas and the revs just drove all the way down it moves a little around 500 rpm then just turns off.

Link to comment
https://www.sau.com.au/forums/topic/307997-help/#findComment-5084997
Share on other sites

O2 sensor is a sensor in your dump pipe that measures air fuel mixtures tell ur ECU if the cars to rich or too lean and then the ecu will balance the car to run appropriately to many definitions google it but thats what it does in a nutshell .... simply purchase one around 70 - 80 bux new... but i suggest you take it to ur local shop to plug it up to their pc to see for fault codes..

yep i think ill take it too cypher and get the guys too have a look and tell me wats wrong

Link to comment
https://www.sau.com.au/forums/topic/307997-help/#findComment-5084999
Share on other sites

yep i think ill take it too cypher and get the guys too have a look and tell me wats wrong

Be sure to let us know what was the problem once they work it out

good to have these questions answered on the forums if anyone else out there as similar problems =)

Link to comment
https://www.sau.com.au/forums/topic/307997-help/#findComment-5085221
Share on other sites

my car was doing the exact same took it to the mechanics this thursday gone and they put in a new fuel pump and done something else cant remember haha but its going sweet as now

hey mate wat mechanic did u go too??

and how much did they charge ya

cheers

Link to comment
https://www.sau.com.au/forums/topic/307997-help/#findComment-5086330
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...