Jump to content
SAU Community

Damaged Skyline R33 Gtst Series 2 1996

perry_r33
 Share

Recommended Posts

  • Replies 210
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

perry_r33 Mentor

perry_r33

Posted
  • Author
Posted

selling a set of mags 235/40z/r18 90% thread on the wheels selling for $800 and will also though in 20lock nuts with the key nuts in anodized red

post-62515-1266740367_thumb.jpg

post-62515-1266740393_thumb.jpg

JadGTST33 Community Regular

JadGTST33

Posted
Posted
selling r33 floor mats parcel shelf and climate control

Hey mate... looks like a nasty dint there!

I'm lookin for a few Series 2 bits to put in my Series 1.

Not sure how much cash i have to spare yet... shoot me prices n we'll see!

I'm in St Kilda, so I'd probably just come pick em up.

Wanting a Series 2 dash/radio surround, complete with gear stick surround (assuming its a manual) and ash tray.

Possibly that rear parcel shelf too.

Curious to what shifter you had in it (once again, assuming manual) stock or short shifter?

Also I'm wanting a pair of clear side indicators, but noticed you've lost one in the accident! :thumbsup:

And lastly, I need the short oil line that runs over the top of the coil pack cover too!

Anything you can help me out with mate?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...