Jump to content
SAU Community

Recommended Posts

ok ive sold my ceffy so the following is up for sale

-RB20det engine complete(90xxxkms on it)

includes

-engine(complete)

-turbo

-coilpacks and coil pack loom

-crossover pipe

-manifold

-HKS dump(used but fitted)

-all inlet side blah blah blah

-mount brakets and engine mounts(preety damn good nick

its a complete engine ready to be dropped in and used

its a left over from my 1via and never used with cef

quick sale

$550ono hell farrken cheap like a chicken coop bitchez

located in vic(craigieburn)

will not post unless i can just stand and watch some one load up and thats as much as i will do

prefer local pick up

also have a r32 s/s front pipe fronm gktech that ive paid for and not picked up i want 50 dollers for

if ur keen i will speak to greg once payment is received and u can ether pick up with my verification number or get sent out for 10 bucks

Edited by green1via
Link to comment
https://www.sau.com.au/forums/topic/308591-fsrb20det-engine-with-accs/
Share on other sites

  • 1 month later...

Hey mate im pretty keen at this stage,

can u pm me? i cant till i clock up 10 posts, lol

im in melb so pick up is ok, if i like it.

so only coil pack loom? or engine loom also?

im not familiar with ceffys, is it red or silver top?

plz msg me mate,

TB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
×
×
  • Create New...