Jump to content
SAU Community

BWCP is terrible

Torrens

By Torrens,
in Queensland

 Share

Recommended Posts

Torrens Collaborator

Torrens

Posted
Posted

Hi All,

Me and the missus went down to the broadwater carpark last night to have a look around and whilst there were plenty of cars to be seen, 90% of them were commodores! :P:(

What has happened to this institution?

It felt weird walking around trying to find a imported car.

So where do the jap cars hang out down there now?

Link to comment
https://www.sau.com.au/forums/topic/31076-bwcp-is-terrible/
Share on other sites
dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted

No offence mate, but where the hell were you looking? With the 'little' cruise me and my mate planed in about 5mins, and then had on a particular brisbane based website for about 6hours, we had HUGE numbers, the majority of which were imports.

So where we went was down the back of the carpark. If you couldnt find anything last nite you mustnt have been looking very hard. The carpark was packed.

Link to comment
https://www.sau.com.au/forums/topic/31076-bwcp-is-terrible/#findComment-627436
Share on other sites
MM2death Grand Master

MM2death

Posted
Posted
No offence mate, but where the hell were you looking?  With the 'little' cruise me and my mate planed in about 5mins, and then had on a particular brisbane based website for about 6hours, we had HUGE numbers, the majority of which were imports.

So where we went was down the back of the carpark.  If you couldnt find anything last nite you mustnt have been looking very hard.  The carpark was packed.

amen

Link to comment
https://www.sau.com.au/forums/topic/31076-bwcp-is-terrible/#findComment-627693
Share on other sites
NismoGirl Grand Master

NismoGirl

Posted
Posted

Most of the crowds of people dont' get down the coast until 9:30 - 10ish. We normally park over the far side of the carpark (towards the pool) with quite a few imports, usually skylines.

You just have to be choosie what dickhead you park next too, and lately, unfortunately, there's been quite afew dickheads

Link to comment
https://www.sau.com.au/forums/topic/31076-bwcp-is-terrible/#findComment-629316
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
×
×
  • Create New...