Jump to content
SAU Community

Power Limit of RB26 Rods?

Sneezer

By Sneezer,
in Engines & Forced Induction

 Share

Recommended Posts

Sneezer Apprentice

Sneezer

Posted
Posted

Does anyone know what the maximum power limit of a standard RB26DET con rod is? At what point do they stretch/bend?

I have been offered a set to put into my RB25DET engine as an upgrade. So I need to know whether it's worth it.

Also you guys talk about Linished rods. Can someone explain what that is please?

Cheers Fellas :P

Link to comment
https://www.sau.com.au/forums/topic/31078-power-limit-of-rb26-rods/
Share on other sites
R32-GTS Mentor

R32-GTS

Posted
Posted

I am told by relable sources and have seen GTR's make 450rwhp + on standard rb26 rods.

I am currently building a rb26 and not sure yet whether to upgrade the rods or not. I think it would be more for security. And with the forged rod been lighter it should revv a bit more freely as well.

hungry6 Experienced

hungry6

Posted
Posted

I can say from a hands on experience that rb26 and rb25 rods are world apart. they have different shape beam the egdes are different also thicker and the most important of all is that the rb26 rod carry a masive bearing end as comparo to an rb25. As for power capacity is all depends on how well u tuned it. But big numbers have been recorded.

Steve Grand Master

Steve

Posted
Posted

Merli, one place that comes to mind is http://www.skylinesaustralia.com/forums/sh...ead.php?t=28130

Steve-SST, who has played with many RB25s and RB26s, is quite adamant that they are the same in most cases, just some RB25s came out with weaker rods, but it appears from his posts that most had the same rods as RB26.

Merli Grand Master

Merli

Posted
Posted

Very interesting read!

I suppose it's quite possible, as all RB25 failures I've seen from excessive power levels have been piston related, which THEN leads to the rods punching holes through the block.

I'm not so sure about the claim that "but some RB 25s have weaker rods but a lot have GTR rods" though... That just seems very iffy and unlikely to me.

Either they all have the same rods or don't. Or all Series 2 and on have RB26-spec rods, or something like that. The claim of:

The only real way is to pull it down but some RBs respond very well to boost upgrades-Exhausts etc and some don't, the ones that don't tend to be the dog motor as the head flows less.

seems like it's based on not enough evidence to me, and based on one or two RB25s grenading and resulting opinion that it had "weaker rods than the rest" and was a "dog motor"

But I suppose Steve-SST has seen a lot more RB25s than I have, so dunno.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Thanks mate.
    • TurboTapin
      Crank Motorsports Front Axles

      By TurboTapin · Posted

      I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Being a manual, we very quickly ordered new R34 gearbox (From Nissan) and remaining parts from Kudos motorsports. Would highly recommend the team there. Ultra helpful and quick to share advice and upgrades. We are in the middle of taking the Auto out (Genuine 94,000/kms) and putting the Manual in this weekend. Part 2 of the build will include likely a Plazaman Intercooler and Plenium, Hks Exhaust with Tomei Dump (ordered).
×
×
  • Create New...