Jump to content
SAU Community

Power Limit of RB26 Rods?

Sneezer

By Sneezer,
in Engines & Forced Induction

 Share

Recommended Posts

Sneezer Apprentice

Sneezer

Posted
Posted

Does anyone know what the maximum power limit of a standard RB26DET con rod is? At what point do they stretch/bend?

I have been offered a set to put into my RB25DET engine as an upgrade. So I need to know whether it's worth it.

Also you guys talk about Linished rods. Can someone explain what that is please?

Cheers Fellas :P

Link to comment
https://www.sau.com.au/forums/topic/31078-power-limit-of-rb26-rods/
Share on other sites
R32-GTS Mentor

R32-GTS

Posted
Posted

I am told by relable sources and have seen GTR's make 450rwhp + on standard rb26 rods.

I am currently building a rb26 and not sure yet whether to upgrade the rods or not. I think it would be more for security. And with the forged rod been lighter it should revv a bit more freely as well.

hungry6 Experienced

hungry6

Posted
Posted

I can say from a hands on experience that rb26 and rb25 rods are world apart. they have different shape beam the egdes are different also thicker and the most important of all is that the rb26 rod carry a masive bearing end as comparo to an rb25. As for power capacity is all depends on how well u tuned it. But big numbers have been recorded.

Steve Grand Master

Steve

Posted
Posted

Merli, one place that comes to mind is http://www.skylinesaustralia.com/forums/sh...ead.php?t=28130

Steve-SST, who has played with many RB25s and RB26s, is quite adamant that they are the same in most cases, just some RB25s came out with weaker rods, but it appears from his posts that most had the same rods as RB26.

Merli Grand Master

Merli

Posted
Posted

Very interesting read!

I suppose it's quite possible, as all RB25 failures I've seen from excessive power levels have been piston related, which THEN leads to the rods punching holes through the block.

I'm not so sure about the claim that "but some RB 25s have weaker rods but a lot have GTR rods" though... That just seems very iffy and unlikely to me.

Either they all have the same rods or don't. Or all Series 2 and on have RB26-spec rods, or something like that. The claim of:

The only real way is to pull it down but some RBs respond very well to boost upgrades-Exhausts etc and some don't, the ones that don't tend to be the dog motor as the head flows less.

seems like it's based on not enough evidence to me, and based on one or two RB25s grenading and resulting opinion that it had "weaker rods than the rest" and was a "dog motor"

But I suppose Steve-SST has seen a lot more RB25s than I have, so dunno.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...