Jump to content
SAU Community

Recommended Posts

So, I may be panicing prematurely, but pretty much everyone who has seen my car so far has said "Nah, that'll get written off" - assessor is yet to see it though. As I'm sure we all are on this forum, I am very attached to my particular car and really don't want it to be written off. But if it does, I'm thinking I'm going to take the money and start saving for either a R33 GTR or R34 GTT... maybe something completely different, I don't know.

The thing is, in the mean time I'd want to buy a car that is as cheap as possible but pretty much bullet proof. I don't particularly care about looks, age, ride comfort, anything other than something that keeps going and going and going. The old mid-80s toyota corollas spring to mind. My old Daihatsu Charade was also a bloody amazing car and nippy too for its little 1300cc engine.

We're talking about sub $1500 cars here - I don't want to eat too much into my budget if worst comes to worst and the 33 is a write off.

So, harken back to the days of your P-plates and lets hear about your best old bullet proof bunkie!

Link to comment
https://www.sau.com.au/forums/topic/313237-bullet-proof-bunkies/
Share on other sites

If you don't mind looking like a farmer or a tradesman look over the episode of Top Gear trying to kill an old mechanical hilux [talking about zero electronics here, except obvioulsy lights/battery etc].

That and, dare I say it, I've had mates with Skylines, and daily Excels that have overcome some phenominal situations.

Edited by That_timothy

I am also thinking of buying a bunky, but more to save kms when the new engine goes in... Will be following this thread.

Should throw good fuel economy into the mix as well, no point having a car that never stops but costs you as much in petrol as it would to service...

I drove thru the hail storm in my 21yr old A31 Cefiro and the only damage was pin prick dents in the roof which u can only see if u look hard enough, all the windows survived which i was sooo surprised about. Awsome hardy car but i would say MOST reliable.

Doh!...Nana is off the table...hairdresser parts are taking longer than expected.

Dude! I thought you'd dropped off the face of the planet, how the hell are you? Too bad about the nanamobile. I haven't seen you in... well.. must be getting on a year and a half. I'm in Balcatta now incidentally.

Assessor STILL hasn't been so I don't know if I'll be needing a bunky or not. I like the idea of a little shitbox to tool around in though - I really hated taking and parking the line anywhere unusual...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...