Jump to content
SAU Community

Recommended Posts

Nah they dont look like that ^ and they say Xenon but you cant see it in this pic.

I have only ever had Cut H7s in it, and thats what was in it when I purchased the car.

Trimmed H7's is what I used when I did a dodgy conversion job to pass Regency (as I run D2R xenons - that's what came with the car when I bought it - freshly complied).

(Side note: I'm sure I already replied to this earlier with pretty much above - but my post seems to have gone missing...)

Link to comment
https://www.sau.com.au/forums/topic/315534-r34-headlamps/#findComment-5167411
Share on other sites

This is what I have been using.

Dont H1s have a different plug thing?

I want to buy some new bulbs tonight hopefully. Just not sure what to ask for.... do the D2R lights come in all different sizes or do I just say D2R?..

Link to comment
https://www.sau.com.au/forums/topic/315534-r34-headlamps/#findComment-5169957
Share on other sites

D2R xenons are very expensive over the counter; You could be talking $200-300 for a pair, easy. Getting them online is a lot cheaper.

However - this assumes you still have the xenon ballast, cabling, plugs, etc to hook it all up to.

A D2R bulb looks like this:

d2rphoto1.jpg

... totally different plug to what you have now. But the base (with trimming), and the light source of the bulb is about the same as a H7 bulb (which is why they're sometimes used for compliance purposes, I believe).

Link to comment
https://www.sau.com.au/forums/topic/315534-r34-headlamps/#findComment-5170021
Share on other sites

Ill have to check if I still have all the stuff to plug them into. Not sure I do... will check tonight.

Might have to do the trimmed H7s again for now! I hate driving with one headlight. Make my car look pov. Hahaha

Link to comment
https://www.sau.com.au/forums/topic/315534-r34-headlamps/#findComment-5170163
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...