Jump to content
SAU Community

Recommended Posts

Unfortunately, due to family and budget reasons, its time to sell my S14.

Ive owned the car for the past 7 years, in which time it has evolved from a standard car to its current specs.

Car details

1995 Nissan S14 S1 200sx

Mid spec

Pearl White

171000Kms

Rego till 5th June

Car has been very well maintained with all servicing done at 5000km intervals or after every three track days using genuine Nissan filters, and top quality Castrol and Elf lubricants.

The car is currently producing 200rwkw as tuned by Indy at IS Motor Racing running 1.1bar. It has been very reliable on the road and track.

Even with the modest power the car has set times up there with the quickest S series cars in the state due to its well setup suspension and braking package. To date the car has set the following lap times

Wakefield Park 1:06.8

Eastern Creek 1:46.9

Oran Park GP 1:19.3

The car also still has air conditioning and a full interior forward of the roll cage and is still quite nice to drive on the street.

Full specs are as follows:

Engine

HKS Step 1 cams

Tomei adjustable cam gears

Splitfire coil packs

Hybrid GT front mount & alloy piping

K&N pod in custom enclosure with cold air intake from front bar

Greddy aluminium winged sump

S15 injectors

Garrett GT28R

JJR 40mm aluminium radiator

Oil cooler with Greddy sandwich/thermostat and braided lines

Braided turbo water lines

Cusco catch can

Nismo Engine mounts

Flyn 3 dump and front pipe

Metal cat hi-flow cat

Kakimoto 3 cat back

Drivetrain

Exedy heavy duty full face clutch

Nismo gearbox mount

Cs short shifter

Cusco RS 1.5 way LSD

4.3 ratio gear set

Brakes

R33 GTR Brembo four piston front calipers

Custom cold air ducting from front bar to inside of rotors

Proconcept 2 piece front rotors

R33 GTST rear two piston calipers and rotors (incl hand brake)

Project Mu HC+ pads front and rear

R33 GTR master cylinder

Cusco master cylinder stopper

ABS has been removed entirely

Suspension

Bilstein Height adjustable coilovers. These have been revalved to a custom setting that I have developed over the past 5 years through my work as a suspension engineer with Bilstein Australia.

7kg front and 5kg rear springs

Custom BBM adjustable castor rods

Cusco adjustable top mounts

Nismo front strut brace

Whiteline adj swaybars front and rear (front bar has had extra holes drilled to allow stiffer setting)

All suspension bushes have been replaced with Superpro nolathane.

Noltec urethane subframe bushes.

Urethane diff mount bushes

Adjustable rear camber arms

Interior

Sparco Pro2000 fixed back seat on Bride superlow rail

Sparco suede dished steering wheel

Scroth Profi 111 6 pint harness (2013 date)

Bond Rol bars bolt in ½ cage with harness bar

JVC MP3 stereo

Electronics

Apexi PowerFC with hand controller

Blitz DSBC

Defi link gauges (Oil temp and pressure) with controller and warning light

Exterior

SSA indy rims 17 x 8.5 front and 17 x 9.5 rear

Bridgestone RE01R, 235 front and 245 rear, over 80% tread remaining

US Racing Sports front bar with custom ducting for brakes, oil cooler and intake

Custom splitter and undertray

JDM grill

Extras that may be included with the car if the price is right

Vented fiberglass bonnet with bonnet pins

R33 GTR rims, 17 x 9 +30 with 90% worn RE55 semis.

Assorted spares and standard parts.

Here are the pics

1.JPG

2.JPG

3.JPG

4.JPG

5.JPG

6.JPG

And here is a pic of the car in action on the track.

Nis_1148sma.jpg

Price is $16,000.

This car would suit anyone looking for a quick, well setup street and/or track car.

For more info PM me, call me on 0409 773 820 or email me at [email protected]

Link to comment
https://www.sau.com.au/forums/topic/317274-fs-s14-s1-200sx-road-and-track/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...