Jump to content
SAU Community

1994 Nissan Skyline R33 Non Turbo, How Are They On Fuel?

zoomzeline

By zoomzeline,
in General Maintenance

 Share

Recommended Posts

mad082 Grand Master

mad082

Posted
Posted

fuel tank is about 65L, best to use premium fuel, but not a must. as for fuel economy, as with every car it really depends on how you drive. if you like flooring it everywhere then you will get noticably worse economy than someone who drives like a granny

  • 2 weeks later...
jjman Mentor

jjman

Posted
Posted

yeah, hence not being fussed about replacing the O2 sensor. I just have that feeling that I should be getting a bit better efficiency from a 2.5 litre 6... But maybe im just getting more and more upset at the increasing cost ($) to do said 100km- aka fuel prices

:P

i think that if your o2 sensor was bad you'd be getting worse than 12L/100kms of "brisk city driving"
mad082 Grand Master

mad082

Posted
Posted

it really comes down to how you are driving. if you are flooring it a fair bit then you will get poor fuel economy, even in something like a skyline with a relatively small engine. they aren't exactly tuned to be economical either. they are tuned to be a bit sportier, so that means that even driving like a granny you would use more fuel than some other 2.5L engines out there.

mad082 Grand Master

mad082

Posted
Posted

i was getting much worse economy than you in my r33 gts-t. i was up around 17L/100kms. on a long trip on the higway it was down around 10 or 11/100kms. new o2 sensor made no difference because it was down to my driving style. the o2 sensor has no effect on how rich the car runs when you floor it. the ecu ignores it once you get into higher load cells on the map. this can be as low as about 40% throttle depending on rpm, etc. the o2 sensor is only used in light throttle applications, so light acceleration and cruising along at a steady speed.

before you go out and buy a new o2 sensor you would be best off just testing your current one with a multimeter to see if it is working properly.

sydking Veteran

sydking

Posted
Posted

il whack in about $50 so half a tank aprox, will last me about 250 k's, but its all driving style. i try and change around 3k rpm but its not always the case haha, and i do alot of stop start driving aswell which dosent help.

jjman Mentor

jjman

Posted
Posted

after getting the new tuned ecu in and boost controller retuned I found that i was in the 20L/100km bracket for 'very spirited' driving. New O2 sensor goes in this week...

Laid waste to an EVO so it was all worth it :3some:

also girlfriend screaming real loud and grabbing the jesus bar and the roof under full acceleration. LMFAO

  • 1 month later...
jjman Mentor

jjman

Posted
Posted

Have put in the new NGK O2 sensor, sealed up the filler cap leak so now have an airtight seal on the petrol tank,

also put on a turbo-back exhaust and done a further tune and now down to 12.5L per 100km for brisk city driving.

Stoked.

Ill flush with injector cleaner and do a final tune and hopefully under 12L...

after getting the new tuned ecu in and boost controller retuned I found that i was in the 20L/100km bracket for 'very spirited' driving. New O2 sensor goes in this week...

Laid waste to an EVO so it was all worth it :)

also girlfriend screaming real loud and grabbing the jesus bar and the roof under full acceleration. LMFAO

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...