Jump to content
SAU Community

Recommended Posts

BOSCH 044

BRAND NEW GENUINE BOSCH 044 700hp EXTERNAL FUEL PUMP (Can also be mounted as an internal pump)

Fittings AND bracket included (This is about $60 alone !)

All up, you are looking at about $250 worth of brand new gear,

Asking $150

Pick up preferred from Blacktown in Sydney's west

Will post.

CONTACT OR SMS ME ON 0413 295 712

Link to comment
https://www.sau.com.au/forums/topic/317558-bosch-044-700hp-external-fuel-pump/
Share on other sites

Simon, have you sent the RB26 covers which I paid for last week?

I have tried calling several times, SMS'd several times, and PM'd you on here, all with no reply.

If you could give me a buzz, that would be appreciated.

Thanks mate,

Mitch.

yeh same,

waiting on responses from simon after paying for my goods...

not getting too far with it..

please get back to me ASAP!

Edited by rad32
  • 2 weeks later...

So Simon Mok, SMOK1106 or "smok74"

You have two choices here, and they are very simple.

1. Fix up the two people who you have wrongfully dodged here

And do so immediately, with proof supplied to myself.

OR

2. Have ALL your details posted here in the bad trader listing.

Address, Bank Account Details, Email Addresses (yes, all of them), phone numbers, Facebook links... the works.

You full details will also be forwarded to Police who I've reccomended get involved in these incidents.

Pretty simple choice what to do here. Don't feed me some bullshit story as you've logged on since rad32/Mitch_Rona have posted here/called/SMS'd/PM'd

Admin

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...