Jump to content
SAU Community

Recommended Posts

1994 Nissan R33 Skyline Black

Great condition interior

Stock Rims

Rego Reading” 208,000 Km’s

ICE:

Pioneer Flip Head unit DEH-P7750MP

Pioneer front 6” Speakers

Alpine type R 2 way 6.5” Rear speakers in parcel shelf.

3 stage Viper Alarm black wiring central locking and siren.

Accessories:

G-Reddy Profec B Dual boost controller

AutoGauge Air/Fuel Ratio gauge

AutoGauge Boost Gauge (Not hooked up)

Autotechnica Steering wheel.

Modifications:

ECU: Apexi Power FC and hand controller tuned to 374 HP 18.5 lb Boost and 10 lb actuator boost

Tein Jap spec coil over suspension

Nismo 550 CC Injectors

Tomei fuel pump

Apexi Pod Filter

Stainless intake pipe

Cold Air Intake pipe.

Catco Hi-Flow metal

3” Cat back to 5” Cannon

Custom CES split front pipe.

Hybrid FMIC

2.5” Stainless steel piping.

Nismo FPR

Tomei 256 deg PONCAMS

HKS 3037 PRO S turbo with 0.82 rear housing. HKS Uprated actuator

Gate Racing timing belt: Changed 4000 Km’s ago with new bearings seals and water pump.

Standard low mount exhaust manifold.

HID 6000K standard headlight kit (LOW BEAM)

Splitfire Coils

Platinum 7 Spark

Turbosmart Plumb Back BOV

Z32 AFM

No Heater.

Engine Rebuild: RB 25 DET

KM’s Since Rebuild 78,000kms

Current Compression test Results: 155 psi across all 6 with 1-2 psi difference

No blow-by

Motor built by Elite Racing Developments.

JE Forged Pistons 25 thou over

ACL Rings

Prepped Rods,

ACL Bearings

Standard valves

Prepped head. No Port or polish.

Notice to all, regretful sale of my line, but due to moving over seas later on in the year I need to pass this onto someone else to enjoy the beauties of the skyline world, and move to saving money, this includes a smaller car. Mods listed above are true and accurate, This car is well treated and driven respectively, it is a daily driver for me to and from work with the rarity of taking it out for a long drive.

Engine oil is changed on or before the 5000 KM mark, usually before as well as fuel filter. Using quality filters and Motul 8100 Fully synthetic oil. Sadly due to 16 years old paint this baby is in need of a fresh coat of clear or heavy cut and polish, hence the price I am asking (Oxidation of the clear coat with one section of clear coat near the rear peeling). The car runs perfectly, and never has missed a beat. A few dints from shopping idiots on drivers side door, though nothing of great concern and easy to repair, and the usual stone chips on the front bar. Overall Good condition on the outside NO RUST!!!!. Will suit someone who wants to get in the modification world with near enough everything already done just a fresh touch up on the paint is all it would really require. Other than that RWC will be supplied on sale of the car. Has 6 months rego lasting to 11th of November 2010. THIS MUST GO!!!!

NOTE: Things that will also be included with the sale.

- Stock Steering wheel and HICAS mechanism.

- 2nd hand fully functional heater core.

- Stock ECU

Price: $8590.00 ONO. Need to sell.

Contact via Message open for discussions/inspection on appointment. Located in the Ipswich district.

More Photos will follow when I have time to take them

post-27175-1272237751_thumb.jpg

Its a great car guys. Went for a ride in it yesterday and it runs like a dream. If I didnt already have a skyline I would have bought it last week.

Edited by TJ_R33
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...