Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 4 weeks later...

spotted a new radar camera on near Woodvale Senior High School this week, initially drove pass with almost no warning (20m out) on my Whistler PRO-78SE, noticed the device was pointing almost across the road not down the road.

drove back around 5 minutes later and the operator had turned it to look down the road, my laser warning went off about 200m away this time

I assume the operator initially didn't set it up right

welcome to the forum wozza69

yer the cop ah probs didnt have it set up right. i know the older ones had to be between set angels to produce accurate reading so i would guess it would be the same for the new ones

  • 3 weeks later...

Since returning to WA I have noticed a set of these on the Mitchell FWY.

http://www.ceos.com.au/pdfs/TIRTL-overview.pdf

Unsure if it has been posed yet. Basicly they are an all in one fix/portable unit that can detect speed/red light camera/traffic count depending on what they set them up for. The ones i have seen are fixed but i have not noticed a camera near by. Ill get a more exact location later, and it is on both sides of the fwy. :D

post-36469-1283755418_thumb.jpg

post-36469-1283755459_thumb.jpg

cheers

PS: Pics are from victoria.

Edited by Boss-zilla
Operational range 15m – 75m

Working distance 10km/h – 250km/h

Enforcement rate > 1 vehicle/s...so are we going to see enforcement trim the photo when there is more than one vehicle in pic???

so the goal is if ur going to speed u better be willing to go over 250km/h :P

Ok, so the set up i was talking about is about half way between Whitfords and Edgwater stations. I think it is only monitoring traffic flow/numbers because i can not see any camera's as we fly by on the train.




  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...