Jump to content
SAU Community

Recommended Posts

I've just found out my passenger side wheel has alot of movement in it. Obviously I'm pissed, as the wheel alignment guys never caught this or told me about it. It's quite noticeable, and I'm sure not safe. So it's time to get it fixed. The drivers side one I'm told has no play, but the rubber ball joint bushing thing looks pretty knackered, so I figured maybe I should just get them both replaced, since I have to get an alignment done anyway.

Now this is the confusing part. The places I have contacted for part #s and pricing, have given me differing #s.

Now these OEM parts are TE926-12 and TE926-14. Not sure which one I'm supposed to order. But as I understand it, the 14 has a longer thread, so that sounds like the one I should get right?

TE926-14

te92614tierodend.jpg

or do I order a ball joint instead?

r32s14rearballjoint.jpg

Do people replace the ball joint and use their original tie rod end, or just get a whole new tie rod end with new ball joint included?

buy the entire outer tie rod end , the part cost $27 each at bursons.... r33gtst and r34gtt are the same i just did this recently.

Ok, will call them up and see what they have. What's throwing me a little is I've been given two different part numbers for my car from various places. Can you recall the part number of the one you got recently?

And did you do both sides or just the one that needed replacing?

Get a set of these

Despite the brand they are some of the best priced around (not to mention one of the greatest brands ever!)

http://www.rhdjapan.com/ikeya-formula-stre...4-a31-c33-20697

and for ends you want

http://www.kts-web.com/overseas/product/arm/tr_e.html

or

http://www.kts-web.com/overseas/product/arm/tr_r.html

I went ahead and ordered some TE 926-14 tie rod ends today from Global Auto for $25 each.

Adam, I'm not planning on ever racing or drifting my car. The ones I ordered should be as good as the stock Nissan ones I already have. I've read quite a few things about the pillow tie rod ends, and how alot of folks do not recommend them.

Edited by KrazyKong
I went ahead and ordered some TE 926-14 tie rod ends today from Global Auto for $25 each.

Adam, I'm not planning on ever racing or drifting my car. The ones I ordered should be as good as the stock Nissan ones I already have. I've read quite a few things about the pillow tie rod ends, and how alot of folks do not recommend them.

No worries eh.

I only mention this as I have read Nissan tie-rods are typically a weak piont. Havn't actually experience a failer myself though...

good luck with it all dude!

I picked up the tie rod ends from Global Auto Spares today. Had a quick look under the car while holding them up and they seemed to match perfectly. Had a trustworthy mechanic install them both for $40 total, and then onto the alignment place which cost $39.

So new parts, new alignment and it cost me $129 all up. A bargain I think, and the car feels so much better. No rattle noise either. And so far from the driving done today, no tram tracking either.

I kept the old ones, especially the bad tie rod end so I could take a picture and post it here for everyone. Scary sight and I could have been in some very real danger had it failed at speed. On both sides the boots had cracked, but on the bad side, there was no grease left. Just crud and sludge. The thread looked dangerously warn from the excessive movement too. For such a quick and overall cheap replacement, I only wish one of the 3 previous wheel alignment places I went to previously had actually told me how bad the movement in my wheel was. Doesn't say much about the import compiance guys either as it was clearly bad even before I bought this car.

Edited by KrazyKong

There were the pics I meant to post about my old tie rod ends.

The "bad" tie rod end...

post-63769-1273498444_thumb.jpg post-63769-1273498513_thumb.jpg post-63769-1273498891_thumb.jpg post-63769-1273498971_thumb.jpg

As you can see, no grease, lots of sludge and this could have caused a very nasty accident for me. There was a huge amount of play in the joint.

The "good" tie rod end...

post-63769-1273499101_thumb.jpg post-63769-1273499451_thumb.jpg post-63769-1273500229_thumb.jpg post-63769-1273500792_thumb.jpg

No play on this one, lots of grease still and apart from the broken rubber boot, seemed to be in good condition.

There you have it. I don't have pics of the new tie rod ends, just the box they came in and part number.

post-63769-1273497588_thumb.jpg post-63769-1273497726_thumb.jpg

But if anyone is interested, I can take some next time I'm under the car.

  • 5 months later...

Easy way to check

jack up one corner, grab the wheel on the left and right, try to move it as through the steering wheel is turning, any play here is the tie rods or rack ends

grab the wheel at the top and bottom and wiggle up and down, any play here is usually wheel bearings

  • 4 months later...
  • 1 year later...

$25.00 GAH! I called up a few places for quotes on Tie Rod ends today & they were quoting me $130 - $150 .. Gonna fake a dudes voice when I call up next!

So you def these will also fit in an R34?

130-150 sounds more like the price of a tie rod the ends are 25 ring bursons.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...