Jump to content
SAU Community

Recommended Posts

gday all!! offers/negotiation on all parts. i dont want Top dollar for them just want it gone if possible.located in melb can send if needed not a problem.

parting out a complete rb20det redtop (MOST parts will fit silvertop rb20det) engine is complete minus turbo let me know what you need and will take a pic accordingly and send it asap if needed.stock engine no upgrades.coilpacks,coil pack cover,tps..ect ect its all there. let me know or make an offer on a part or full engine ....if you want full engine..faster you get it the cheaper ill do it as time is not on my side and will cost me to take this with me.

r33 s2 turbo - never seen past 9psi in its life (stock boost) came off s2 rb25det engine with 82,000kms on the clock.

r32 gtst front seats - no rips or tears 2 mint front seats with rails.

r32 gtst rear seat - bit second hand but if needed it there

r32 GTR injectors - 444cc x6 - garanteed to flow fine,tuned out to small for my setup

race bucket seat - no brand as far as i know bit used,needs bottom pad and a basic recover but good nonetheless,no rails

r33 stainless steel hand made exhaust - awesome quality!!! hand made with "cake peice weld" type bends MINT!!

guard roller - brand new in box never used,bolt on hub type

180sx pop up head lights - with motors and brackets,1 VERY small dent (somwhat pin size) dab a tad of filler and done.

PERFECT s13/180sx dash - no cracks very good nik

autometer procomp liquid filled water temp gauge - 2 1/2" (i think) or 2 3/4 perfect working order (not half filled like most of them nice and full)

rb25det altinator - good as it gets does its job well

will be updating as things go along have heaps more parts (turbo timers,spare turbo parts*heaps*,tid bits stock coolers ect) or let me know if you need somthing and there is a damd good chance ill have it.

PM,post or sms anytime 0423472263 or call after 6pm please.

thanks very much

J.R

*EDIT*

may be looking to get rid of this piping as im moving to a ff plenum and a top mounted turbo.

just the pipes in bay including blue crossover and HKS (copy) bov.

basically the 2 pipes coming from cooler i will be keeping.

not sure if i want to get rid of it yet but a half decent offer will prob see it go.

post-60301-1272945971_thumb.jpg post-60301-1272946120_thumb.jpg

Edited by Drift Engage House
no worries you will not be dissapointed mate.PM with details sent.

rb25det turbo *SOLD*

hey mate I don't feel comfortable putting my adress details on the forum. Could you please pm your mobile so I may contact you ??

not to be rude peeps but silly offers like $60 for GTR injectors will be ignored.

turbo,coilpacks *SOLD* lots still here =D

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...