Jump to content
SAU Community

Blown Fuse ... Or Something Worse?

pudogg
 Share

Recommended Posts

pudogg Explorer

pudogg

Posted
Posted

Hey guys, has anybody experienced this before?

This morning when I was about to start my Vee, the car lost all power to its systems and the alarm triggered.

There were no lights on the dash, the alarm was not responsive to my remote, the flashing immobliser light on the dash was not flashing (both stock and aftermarket), boot release not working, windows auto adjustment not working, etc etc. The alarm rang for a good 10 minutes before it died out.

Any thoughts or suggestions on what I should do? A fuse I can check perhaps, or need to have the car towed to an auto electrician / immobliser fitter?

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/319527-blown-fuse-or-something-worse/
Share on other sites
rb26stagea Grand Master

rb26stagea

Posted
Posted

Sounds like a flat bettery to me: the alarm should have a backup if it's decent, which would explain why nothing but the alarm worked...

I had a similar incident: got back to my car to find the brakelights strobing like crazy: tried to start it, and nothing, except I could hear a relay going crazy (clicking)... Turned out I'd switched the foglights on by accident when I indicated to park, and they stayed on. A quick jump start and a short drive, and it was all sorted.

Maybe have your alternator checked?

pudogg Explorer

pudogg

Posted
  • Author
Posted

thanks for your posts guys. i too am hoping it's a weak battery esp considering that it was cold this morning in Perth.

but the car started without fuss yesterday. when i inserted the key this morning everything lit up as it normally does before the power cut happened and the alarm sounded. yes it's probably the depleated battery for the alarm that stopped the siren after about 10 mins.

lol @ headlights not turning off when battery is weak!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...