Jump to content
SAU Community

Recommended Posts

Hi

Just bought a 1993 R33 with rb25 engine, non turbo

car needs filter and full piping to fuel injection manifold. rather than pay for stock parts i want a performance filtration system

any ideas about what to put on it??

Any good performance shops in melb that will do it for reasonable price??

yes there is...its the snorkel off the front of the box.

even the very best cold air setup would be worth what 3-4hp?

its hardly worth it.

Yea the snorkel. It doesn't look like much cold air could get in between the narrow gap between the bonnet, thats why i thought an intake would be better. Thought it was there just to look good.

Filter. I'm thinking of putting in an apexi power flow, ive heard its a great filter. Any other reccommendations?

Just put a good pannell filter in the stock box, the run a 2" hose from outside the engine bay to the inlet on the stock box.

That is unless you want the fully hecktic tuner look for your NA! ! ! ! slow liner...

Just put a good pannell filter in the stock box, the run a 2" hose from outside the engine bay to the inlet on the stock box.

That is unless you want the fully hecktic tuner look for your NA! ! ! ! slow liner...

Ah k yea that sounds sweet. Any reccomendations on a good performance panel filter brand?

Non oil type K&N (oil messes with the air flow meter).

Most of the major brands have drop in replacment washable filters...

Just keep them clean- really clean- all the time. A fresh new filter can get you 6-8kw, a dirty new filter will robb you 10.

The Stagea guys, me included fit a cold air deflector and use an oiled Red Line or similar. I am fitting a Forward Plenum and have had to go pod. I have fitted a bend and tubing thru the OEM smic hole and the air goes directly to the pod.

The Stagea guys, me included fit a cold air deflector and use an oiled Red Line or similar. I am fitting a Forward Plenum and have had to go pod. I have fitted a bend and tubing thru the OEM smic hole and the air goes directly to the pod.

Hey ol buddy... Loose the oiled filter. You allready have problems with your air flow meter-

If you must go to a pod, make up a heat shield to box it in.

  • 1 month later...

The previous owner of mine put in a K&N, so i reckon it probs a good idea to get rid of this.

Btw someone told me that if you remove all those fins inside the air box you might get some more power and a bit of a whining noise.

Edited by Duchie

Get a HKS mushroom pod, pop that where the factory airbox goes. Make/buy a box and give that box at least one large feed of cold air from under the car or from behind bumper, preferably two.

Will be much better than factory airbox imho. You will gain valuable kw's for an n/a engine and the engine will also rev more freely meaning increased acceleration.

I see many people saying intake is useless, factory airbox etc but it comes down to personal expectations imho. Just consider the person saying it's useless might be someone that expects at least 20rwkw from a mod or something especially if they have a FI car. I love n/a's myself and have noticed even 5wkw difference and given the chance again, would do all the mods again haha.

E.g. On my previous car (v35), alot of people say it's not worth doing intake, just stick with factory box and put in a panel filter and a smoother intake pipe.. i had that for awhile then changed to a HKS cai kit and noticed the difference easily and straight away. Two other passengers did too - Gave very different characterisics.

Edited by Touge Kyousou

I've seen those articles too and i've also seen another where the HKS was rated very high (albeit poor filtration - you can see it too by holding the HKS element up against a light source).

Shortly after seeing those flow test articles, i went out and bought a couple of 3a racing pods to try out against the then installed HKS mushroom (on an FTO). To be honest, i felt the fto was better (slightly) with the HKS mushroom. An inconsistency though was that the HKS had a larger mount whereas i had to use a reducer for the 3a onto the aftermarket big pipe so that may be why the hks felt better.

Using the K&N may affect your maf.. ? I'm unsure if the pods from k&n are wet or dry (panels are wet). My old man has a couple laying around and i might try it on the line. No idea on the apexi ones though!

though on the well covered test by hot 4's (i think?) the HKS mushroom filters sucked at both filtration and flow!

The article recommended K&N, APEXi or 3A Racing (cheap arse brand)

Get a HKS mushroom pod, pop that where the factory airbox goes. Make/buy a box and give that box at least one large feed of cold air from under the car or from behind bumper, preferably two.

Will be much better than factory airbox imho. You will gain valuable kw's for an n/a engine and the engine will also rev more freely meaning increased acceleration.

I see many people saying intake is useless, factory airbox etc but it comes down to personal expectations imho. Just consider the person saying it's useless might be someone that expects at least 20rwkw from a mod or something especially if they have a FI car. I love n/a's myself and have noticed even 5wkw difference and given the chance again, would do all the mods again haha.

E.g. On my previous car (v35), alot of people say it's not worth doing intake, just stick with factory box and put in a panel filter and a smoother intake pipe.. i had that for awhile then changed to a HKS cai kit and noticed the difference easily and straight away. Two other passengers did too - Gave very different characterisics.

Why would you do that?

all it does it suck in hot air which = less power

How would that suck in hot air ? The pod will be enclosed/sealed from the rest of the engine bay and then there will be at least one preferably two large pipes ramming cold air from the front/underneath of the car into that box/enclosure.

??

Edit - Also if the air is slightly hotter but the resistance to flow is much less, you should still have on road gains being the engine will rev easier but now that's really cutting it thin lol.

Edited by Touge Kyousou

Hi all,

From what i have read in these threads it seems the K&N filter is not a good filter to use and the reason being is due to the filter spray which they recomend to be used on their filters.What happens if you don't use the spray and if you do only use it lightly.Do you guys think this could be a plan or would i be wasting my time, i hope not as i've just ordered a K&N panel filter and it should be here after the weekend? I have a V35 250GT. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...