Jump to content
SAU Community

R32 Bits

Rb20_180

By Rb20_180,
in Classifieds

 Share

Recommended Posts

Rb20_180 Collaborator

Rb20_180

Posted
Posted

Hi All,

i have a few bits and pieces out of my half cut and out of my gtst shell. everything open to offers.

also stripping half cut so anything u can think off that i havent listed just ask.

Everything out of R32 GTST Type M

will get picks up soon or can email.

Untouched front reo $50

Type M factory side skirt $250, couple of scuffs nothing to major.

3 headlights all mint

2 RH $75ea

1 LH $75

Rear inside side trims (mint) $50pair

Clutch & brake pedal plus clutch pipes (Master&Slave cyclinders leaking) $75 all (can supply new slave for $58)

Dash (mint) $120 with good vents

Climate control unit $20 also have wiring and a/c mode box (offer$$ and il remove)

Instrument cluster $100 (140,xxxkms)

LH lower control arm $50 (ball joint good)

Washer bottle with both motors $25

r33 RB25 crossmember $60

MDU front coilovers $250 base height adjustable, 17 dampner

6 CA18det coilpacks with plugs $50

Located on the sunny coast qld

pm me

Ry

Link to comment
https://www.sau.com.au/forums/topic/320783-r32-bits/
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Hendasto
      Lets play a game - What is causing my oil consumption?

      By Hendasto · Posted

      Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • Hendasto
      Are RBs worth building reliability wise

      By Hendasto · Posted

      At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...