Jump to content
SAU Community

Recommended Posts

Hi All,

I am trying to further understand the rear suspension of an R32/R33/R34 skyline. I have done a lot of searching and reading. I am confused with the terminology as different people use different terms to describe the same suspension component. It seems there are three main suspension components in the rear of an R32/R33/R34 skyline.

I am wondering if someone could help line up the following:

Quote from Tarmac:

Lower control arm bushes

Rear Traction arms

Quote from Sydney Kid:

Just to make sure we have this covered, there are 3 links (each side) in the rear suspension of an R32/33/34;

1. Upper Control Arm, this mostly adjusts the camber, but it does change the static toe a small amount at the same time

2. Traction Rod, this mostly changes the dynamic toe (bump steer), but it does change the static toe and static camber by small amounts at the same time

3. Steering Arm, this changes the static toe (HICAS connected or disconnected)

Where are the lower control arms?

Quote from my suspension place:

1. Upper Control Arm

2. Lower Control Arm

3. Steering Arm

Where are the traction rods?

I am assuming traction rods = rear traction arms ?

Can someone please help match up this different terminology.

Edited by Harey
  • Like 1

Come on fellers, I spend a lot of time on this forum helping other people out, it would be greatly appreciated if someone could help me out with this.

Would also be good info for other people in the future.

Lower control arms are front and rear. On the front they are connected by a ball joint to the front sub-frame and another ball joint to the hub. On the rear they are connected to the rear sub-frame by two bolts and a ball joint to the hub. All of this is for a 32 GTR so I'm not sure if your GT-T would be different.

Traction rods are found on the rear as you suspected. You can see them behind the the wheels and are angled back in towards to centre of the car-(ish).

In the pictures below on the left you can see the rear setup. The short red arm towards the rear is the traction rod and the black arm at the bottom is the lower control arm. In the picture on the right the shiny arm on the top is the upper control arm, this one is after market but you get the idea. The lower control arm is just visible behind the hub.

Is that what you were looking for?

post-8807-1274326301_thumb.jpg

post-8807-1274326315_thumb.jpg

Edited by jonn
  • Like 1

Sure, 1 is the upper control arm, 2 is the traction rod and 3 is a HICAS rod (this is to disable the rear steering setup) your car will probably have the HICAS still installed and it will have hydraulic lines going to it.

All the parts in the picture are aftermarket but gives you the general idea.

Sure, 1 is the upper control arm, 2 is the traction rod and 3 is a HICAS rod (this is to disable the rear steering setup) your car will probably have the HICAS still installed and it will have hydraulic lines going to it.

All the parts in the picture are aftermarket but gives you the general idea.

Hi John, could you please advise if the aftermarket suspension replacements sold by the likes of eg:JJ are actually street legal? I am in Queensland for road transport laws?

I have HICAS lock already installed in my R34 GTT.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...