Jump to content
SAU Community

Damaged R33 Gtst Series 1 - Minor Damage

EXTR33ME
 Share

Recommended Posts

EXTR33ME Enthusiast

EXTR33ME

Posted
Posted

Hi Guys,

Selling my Series 1 R33 Gtst, 1993 model Skyline. I'm the first Australian owner, have had the car for a little over 2 years. Someone backed into the rear quarter, so it still has some damage. Also the drivers door and guard need some paint work. Basically the whole drivers side of the car could do with a respray. The front bar and bonnet need some attention too.

It has roughly 120,000 klms on the clock. I haven't had any mechanical issues with it at all, except for when I first got it the coils needed replacing - runs extremely well.

Registration ran out on 18/05 and I'll be selling it unregistered with no rwc. It shouldn't be too hard to re register, take the boost controller off and the pod filter maybe, that's probably all it needs.

It hasn't had too much work done to it, it has the following mods:

Splitfire Coils

Exhaust from turbo back

R34 side mount intercooler

Pod filter

18' XHP Wheels - tyres around 60% tread. All wheels have gutter rash.

Manual boost controller - pretty much turned down.

Timing belt was replaced with a Gates timing belt at 109,000 klms in September 08. Since then, it has been driven from Sydney to Melbourne and has only travelled 11000 klms including that drive.

It has an Alpine CD & Tape player, with alpine speakers all round including tweeters.

It has the original skyline floor mats

I had bought another boot with drift wing from someone on here, but the fktard couriers dropped it I think ( see photo's). Will include the boot. Also will include the stock R33 side mount intercooler.

There are a couple of cracked hoses in the engine bay - you can probably see my dodgy tape up job. I'll be looking at getting them replaced.

The car hasn't been thrashed, it barely gets driven at all unfortunately.

Looking for $5000 for it. I was quoted about $1000 - $1500 to fix the damage and respray, but that was in Sydney. I don't really have the spare cash or the time to do it, so I've decided to sell it as I need a van for work.

I can be contacted on 0458 333 444 or by PM.

Photos can be seen on this post until I have time to put them on again:

http://www.skylinesaustralia.com/forums/Wr...91#entry5245691

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      R34 GTT owner

      By PranK · Posted

      Welcome to the site. Any more pics? That colour is gorgeous.
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      I didn't even know that existed!!! Amazing, good work Andy at Haltech! A bit off topic here, but I actually met Andy at a Aus Lancer car meet at the old Shell Space Station in Ryde back in 2003 or so. He brought out this aluminium case and showed everyone this basic circuit and said he was making an ECU that was capable of using closed loop to self tune. Most of the people there dismissed his idea.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I actually was using 4D tables with my old AEM WMI system. I'm now using "Water Injection Advanced" under engine functions to control my WMI. The timing and fuel corrections are easier to use as they have WMI in mind. Example, my fuel correction is based on my WMI solenoid duty cycle, they also included built in timers to delay corrections before and after spraying, timers to ramp up pulse width, etc.   
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Just a thought, how come you didn't use a 4D table? So you essentially run 2x fuel and 2x ignition tables, and the table/map switch is handled when there's enough WMI pressure detected. This is mine, but using the flex sensor as the 4th dimension, note the slider at the bottom. Between 0 to 70%, the timing is blended/interpolated , once it goes past 70% ethanol full send
    • 677_GTR
      First time Skyline owner

      By 677_GTR · Posted

      Hi guys, after dreaming of owning a JDM legend for 20 years, I got the chance to buy a 1995 R33 GTR.  I live in a small country called the Solomon Islands which is in the pacific. There is no performance car scene here, however 90% of vehicles here are 2nd hand Japanese imports so there is a handful of JDM sports cars here, tucked away.  3 Evo VI’s, 1 180sx turbo, 2 GTO’s, 1 R32 GTR and 2 R33 GTR’s.    Only 1 Evo and a 33 (mine) are active. I’m hoping to set up a club to get these cars back in the road.    I’d known of my GTR for 9 years and always dreamed of owning it. At the start of this year I found it sitting outside a workshop waiting for a respray. It was in pretty bad shape, although running and driving perfectly apart from a big exhaust leak and worn out bushings. My brother in law who is a huge GTR guy came over for a holiday and I took him to see it, he got into my ear and I bought the car 2 weeks later as is.   I’ve had a pretty bad problem with alcohol and weed since 2020 and I really wanted to quit. So I used this as my motivation. I quit everything cold turkey and have been investing all my spare time into restoring this car. It’s honestly been the best experience and has been such a positive impact on my life.  There is no market for these cars here, no parts and no mechanics that can work on them, so if you wanted to sell one it would be pretty impossible unless you found the right buyer. After a bit of negotiating with the previous owner (a good friend) I got the car for $15,000 AUD ($85,000 SBD) which is insane.  I’ve almost finished doing a refresh on the engine, new turbos, spark plugs and split fire coil packs. Also new gaskets and seals, This car had no leaks to begin with, but it’s due now being 30 years old. . Next I’ll be working on the suspension, all new bushings, ball joints, king pins and new coil overs.  Then it will be body work, it has really bad rust in the boot floor, I have purchased a rear beaver cut from my bro which will replace the rusted out one. The car is originally KL0, but was burnt orange when it landed here, then it was resprayed toxic green and then Bayside Blue. I’m probably going to get it redone in Bayside Blue.  I’m super grateful to be able to enjoy this car and couldn’t have done it without my bro Chris from OG-JDM. Looking forward to the future with this car and hoping to get it on the runway at the airport here 😂  cheers fellas 
×
×
  • Create New...