Jump to content
SAU Community

R33 Wipers Wont Stop

DamageInc

By DamageInc,
in General Maintenance

 Share

Recommended Posts

DamageInc Grand Master

DamageInc

Posted
Posted

my wipers on my 33 wont turn off :blink:

have replaced the stalk , checked all the fuses , they're fine

then i went to check the brown box near the booster and well , it doesnt exist on my car ...

checked my parts car and THAT has one , with wiring that goes down the inside of the strut top and to the front of the car

any ideas how to fix this issue ?

i would like to turn my wipers off without having to pull the plug out of the stalk everytime i dont want them on ...

Link to comment
https://www.sau.com.au/forums/topic/321904-r33-wipers-wont-stop/
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

it may be that the motor is shot. not really sure about the brown box thing, and can't really go look at a car to see, but my grandfathers camry had the wipers start playing up. they were driving along and the wipers just started going mental. turns out that the voltage regulator in the alternator had let go and it was charging at 18 volts. other than blowing pretty much every light that was on at the time, it also fried the wiper motor (even though the wipers weren't on at the time) and then, even after the alternator was fixed, the moment the key was turned on the wipers would go. only fix was a new motor

DamageInc Grand Master

DamageInc

Posted
  • Author
Posted

ive just swapped the motor with a series 2 one ,

doesnt line up properly but the plugs the same (running series 2 engine etc) and its not the motor thats shot

and ive replaced the stalk

so not 100% sure what it could be

any chance it could be the alternator?

my battery has been loosing charge over night in the last couple of nights come to think of it ...

mad082 Grand Master

mad082

Posted
Posted

that's probably just winter killing the battery (happens when the battery is old and then the temps start to drop).

easy way to test if it's the alternator is with a multimeter.

could be anything really. could be that box you are missing. could be just a dodgy wire earthing out.

DamageInc Grand Master

DamageInc

Posted
  • Author
Posted

yeah, im not 100% sure :(

my car was on defect for a couple months therefore not getting driven so i think the battery is on its way out anyways

was going to wire up a switch for the wipers but its easier said then done , and by doing that i wont have a "home" sensor on the wipers so will have to switch them off when they are

at the bottom of the windscreen -.-

waiting to hear back from a mate who knows skyline wiring back the front but at this stage ill have to get my hands on a multimeter and test the alternator

electrical stuff like this does my head in !!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...