Jump to content
SAU Community

Recommended Posts

post-9688-1274928735_thumb.jpg

NOTE: THIS IS A 4WD MAINLINE 1200HP DYNO, 2WD & 4WD CARS CATERED FOR!!

Entries are limited, PM myself or contact Nick on the details listed in the flyer above.

Hope to see you all there!

Should be plenty of 300rwkw and 400rwkw cars in attendance! May even see 500rwkw+ :bunny: .

Cheers.

Ben

Edited by tas_180
Local 500rwkw cars???

I'd better step it up a notch for the re-build then.

Ha ha..

Justin.

I think 510rwkw is the most so far, not bad considering he's been open a month haha!

RB26 with GT4294R will be tuned next week, should go alright :(.

It says 3 dyno runs, are these consecutive? Can you make adjustments inbetween? (aka a low and high boost run)

Yes consecutive.

Boost adjustments are fine :(. No major adjustments though as time for each car is limited (to ensure everyone gets their go).

Cheers.

Ben

Yes consecutive.

Boost adjustments are fine :(. No major adjustments though as time for each car is limited (to ensure everyone gets their go).

Cheers.

Ben

Uh ok no worries. I just wanted a low boost (Daily) read out, and a high(er) boost (with water + methanol injection) read out, 10 sec job.

Ta,

I think 510rwkw is the most so far, not bad considering he's been open a month haha!

Oh Crap... What was that???

RB26 with GT4294R will be tuned next week, should go alright :yes:.

... Yeah I don't know if I'm THAT keen. hah a ha.

The guy needs a T-Shirt.... "GOT LAG?"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Why are you so adamant on going M12? Why not follow Brad (GTSBoy) suggestion. You're talking moving from a 1/8" size, to a 1/2" effectively. 4 times bigger. Why skip the commonly available sizes in between? The bigger you go, the more likely you are to strip the threads out at a later date, as guaranteed, someone will put a huge spanner on the M12 and really tighten it up, and you're only in thin wall, so not a lot of threads to engage!
    • Hi. Yeah thanks. Car is already at tuners and it staying there to resolve "many" issues they do not like. So it is in a good hands. Getting a good tune on that Nistune ECU too so the car would be good. Just needs a little tune up and love.
    • Probably gonna remove manifold and turbo. I’m not sure if I can get M12 x 1.5 air tight. Could use high temp Loctite 246 or something similar, but I don’t know. Maybe it’s just best to remove everything again and weld an 1/8NPT on there instead.
    • Yeah, saw the ratios, not impressed. Would like the punch I have in the first gears now. With those ratios it won't be the same.  Also want the h pattern gearing, or at least a quiet gear set that don't need to come apart for service each year. Looks like the only "reasonable" way Is a 8hp70 transmission, but where is the fun in that🤷‍♂️
    • Hey mate, really appreciate the help. Have been looking pretty extensively myself and was certain they were retro fitted, but then ended up finding a 4 door with what looks like the same side skirts or at least the closest I’ve seen. The photos from the Offset Kings event at Sunrise 2016. https://fatlace.com/offset-kings-okayama-at-sunrise/
×
×
  • Create New...