Jump to content
SAU Community

Help Quick! :) How Do You Remove The Intake Pipe To The Turbo On A R33?

TUF250

By TUF250,
in Engines & Forced Induction

 Share

Recommended Posts

TUF250 Proficient

TUF250

Posted
Posted

HI everyone, I am putting the factory airbox back into my r33 gts-t as it came with a pod filter when I bought it.

While I had the afm out I thought I would remove the intake pipe to the turbo as there is a bit of crap in it and check the turbo shaft play.

The thing is the hose clamp to remove the intake pipe is burried quite deep, i read somewhere here that its a '5min' job to get it off... what am I missing because from what i can see a WHOLE lot of stuff has to come out.

what am I missing and what is the minimum amount of things that have to be removed?

thanks!

boostn0199 Grand Master

boostn0199

Posted
Posted

it is a 5 min job all you do air box off then take off the two standard cooler pipes and youll have room to stick your hand in with a ratchet to undo the clamp on the intake.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • GTSBoy
      R34 25GT Engine Light 21

      By GTSBoy · Posted

      If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...