Jump to content
SAU Community

Heaps Of Rb20 & Rb25 Bits And Pieces.

jutto87
 Share

Recommended Posts

jutto87 Enthusiast

jutto87

Posted
Posted

Ok here goes its a long list so read through and hit me with what you need. :)

Theres no pics due to so much stuff and u all know what it looks like. will provide pics on items pending interest. :blink:

all items are in good order and im willing to post smaller stuff if you pay postage.

Parts located North Brisbane. contact me on 0430 218 339 (Justin)

Random Stuff

Razo turbo timer ( this used to start my car in the middle of the night so ripped it out :blink: ) $40

FET turbo timer $20

R33 Trial rear bar ( just a F'glass copy i think, painted in the factory maroon colour needs some small repairs ) $100

RB30e from vl complete minus loom has everything. came out of a calais??? supposedly $100

RB20 stuff

Stock turbo heatshields $30

Stock Turbo (has shaft play good for temporary fix) $20

Stock dump pipe x 2 $20

RB20 radiator shroud ( mint condish ) $50

RB25 stuff

Stock inlet manifold (in two parts currently no throttle body) $30

Washer bottle x2 $10

coolant bottle $5

Heaps of valley/coil covers $20

Stock BOV $40

Cross over pipe ( painted black has wolf air temp sensor in it aswell :) ) $40

powersteer pump x2 $40

starter motor x2 $40

Alternator x2 $40

R33 radiator out of series 1 manual ( mint condish ) $100

turbo inlet pipe ( the rubber one ) $20

Cam gear cover x2 $20

series 1 Cam Angle Sensor $65

Clutch fan ( think this came off a rb25 ) $40

series 1 manual ECU $60 (i used to run 15 pound boost and do 220kmh with this ecu installed) made 230hp on Powercruise dyno?)

series 1 loom ( possibly modified as it had a microtech computer previously. missing AFM plug ) $100

series 2 coilpack loom $30

r33 dash from 95 model $30

r33 steering colomn and steering wheel ( steering wheel perfect but missing airbag part ) $50

Im willing to meet with people half way depending on how busy i am but always willing to help fellow sau ' ers out so just ask.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/323442-heaps-of-rb20-rb25-bits-and-pieces/
Share on other sites
jonesl Experienced

jonesl

Posted
Posted

hahah. My turbo timer use to do that aswell.

I thought someone was steeling it so i ran out side with a Pole.

you can program them to start at a certain time.

IE, 5 minutes before you leave home so your car is warm.

awsome feature.

good luck with the sale's =P

jutto87 Enthusiast

jutto87

Posted
  • Author
Posted

ha i did the same too first time it started itself. was like WAT THE?? wheres my pole. lol. couldn't read japanese so just ditched it. probably english translations somewhere for it but had an apexi one so used that instead.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...