Jump to content
SAU Community

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

have to space the swaybar down 10mm to clear the sump,

trimmed the bonnet bracing and some minor engine mount mods but the bonnet can be closed!

R34 or a remote master cyl setup still needed to clear plenum.

Slowly getting there.

  • 2 months later...

f**k me,

since I last took these pics, Ive done sweet f**k all.

Soo hard to access the ceff, going to the US in a couple weeks for a car/car parts buying trip, after that, bringing it home.

As it has to sit on the naturestrip (im dreading this) i'll fit some stock wheels amd full the steerer and gauges out of it.

  • 1 month later...

Not much of a update,

Finally back from the good ol USA, picked up a few bits for the shitbox while I was there.

Needed new gauges, brought some autometer "golden oldies" style gauges.

Being a rat/ hot rod/ sled lover, couldnt resist.

12" thermo fans, 2 of.

and some -10 fittings for my oil cooler.

Currently starting to be overgrown in a mates backyard due to the rain melb has been getting, its a sad sight.

Bringing it home soon to do the cooler piping.

Suggestions on what material?

Keep in mind I can weld mild steel and stainless, DIY is gooooood.

problem with that is I have a high mount and a front facing plenum with a q45 TB, so most of that piping will need work.

And most of the generic piping kits are 2.5, cant get a silicone hose that will go 2.5inch to a massive throttle body :S

  • 2 weeks later...

Abit of progress this week,

Although its a 40odd minute drive to get to the car, ive been enjoying the working conditions.

(no dog, no kids and a carport to work under!)

cooler piping is mocked up, just need to take it some where to get tig'ed up.

Initially I started to do it from stainless, the intake side come up a treat, but the turbo side required tight bends, so a mixture of cast and mendrel bent alloy was used.

Pic shows what it will look like, used a existing hole so its neatish, and will give me a heap of room for the airbox i'll start making when the cooler pipe is all welded up and bolted in.

Airbox will also cover up some of that wiring, which is a good thing.

Will also be fitting a oil catch can in the same area, basically mounted against the side of the radiator.

dsc00932rm.jpg

Uploaded with ImageShack.us

Wired in 2 12" thermo fans, brought these in the US, 55mm odd thickness, $52 each from memory.

Ran the wiring for them along the sides of the radiator for neatness.

Started to relocate the battery to the boot, just waiting on a battery now so i can finish it off.

Also started to wire the new gauges in, removing the old birds nest took some time, need that battery to sort out power sources to power the gauges.

here what they look like, 'oil temp' wasnt available in this style, so opted for 2x water temps.

dsc00933mh.jpg

Uploaded with ImageShack.us

Most of the big stuff to get it running is done, just ip to the small time consuming 'custom' stuff, wiring extensions, genrally just cleaning the bay up and mounting parts properly for a change.

Also got a longer throttle cable today!

random pic of my latest "investment" that will land hopefully early january.

Need to do a service and carb rebuild on it before I sell it.

Want a car or motorbike shipping from LA to Aus? Inquire within, I do good rates :D

dsc00847e.jpg

Uploaded with ImageShack.us

Thats about it, look out for more updates, the closer it gets, the more pumped I amto work on it.

Goal: tuned by early Feb.

Edited by works 510

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...