Jump to content
SAU Community

Recommended Posts

he guys

bought a kus enginnerg plenum big mistake

anyways the coolant line need to be modifed dose anyone have a clue what has to be done excatly cuz im outter ideas.

i really need help on this one as its just pissen me off if anyone has done it would appreciate the help .thanks

Link to comment
https://www.sau.com.au/forums/topic/324897-kus-engineering-rb20-plenum/
Share on other sites

The pipe underneath?

Cut it (around an inch or 2.5cm in metric.).

Weld it.

Happy days.

You will understand where you need to cut it once you have a good look with the pipe underneath.

I would also suggest getting the face of the plenum machined, mine was warped and cracked when it was torqued down on the head.

The pipe underneath?

Cut it (around an inch or 2.5cm in metric.).

Weld it.

Happy days.

You will understand where you need to cut it once you have a good look with the pipe underneath.

I would also suggest getting the face of the plenum machined, mine was warped and cracked when it was torqued down on the head.

yeah that bithch of a pipe ....how u get that to line up with the other bit without the hose kinkn ?

also where did u get your refaced and a rough price ...also did u have troubles with the thermosts housing ....thanks heaps man

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Some troubleshooting, connect up a timing light/gun with a proper ignition lead on coil 1. Hold the revs at 4~4500rpm and see if your timing is all over the shop, scattering off its tits. If so, there's a high chance your CAS is fked. But I read you have a Link ECU ready to go in, why not just skip all this and put that in - will make troubleshooting so much easier.  
    • Misfires when the car is fully warm are generally attributed to the coils (and/or the igniter, on cars with a separate igniter). They can stop working properly when they get hot for a number of reasons. Either electric/electronic, or from thermal expansion opening up gaps and allowing HV leakage. Seeing as you have replaced the coils, that could/should rule them out. But I wouldn't always assume so. Were the coils genuine? Or is there a chance you have bought some counterfeit Chinesium shit? Then we're back onto loom connections. They can fail when warm/hot for the same reasons. Inspections, cleaning of contact surfaces, ensuring that terminals are fully inserted, etc etc, are all justified. The same (heat effects) holds true for the other electrics and their connectors. AFM & CAS, primarily. If you try that Chinesium AFM, drive it around on low load until it is properly hot, but do'nt give it more load than you have to, except when you need to see if it will still miss. I'm dead serious about the untrustworthiness of the calibration of those copy AFMs. Injectors are unlikely to get hot unless the fuel is coming back around hot. You could try squirting them with compressed air or freeze spray to cool them back down to see if they are maybe the cause.
    • Alright, all the plugs looks good. Noticed that it starts to get bad when the car is up to temp, that's when things starts to misfire hard. next to do is Injector cleaning and such. Got in touch with a shop to do work on the injectors next Monday also help on diagnosis.
    • House of Fatz dry dock needs a clean sadly one of the long time stables is leaving this weekend   see ya mr purple
    • Hence why I've only modified my car into a pure daily. Everything has to remain reliable & roadworthy, while providing value and grin factor. It also must not be handcrafted to the extent that the car will be immovable if something breaks because you cannot get or make a replacement to at least limp around with.
×
×
  • Create New...