Jump to content
SAU Community

Recommended Posts

Hi all i am selling my 1989 r32 4 door rb20 turbo. It is in reasonable condition couple of marks here and than it is pretty much stock. I has 89 000 km on the clock and has march 30 2011 rego.

It has the following mods.

1. 3 inch Cat back exhaust

2. Apexi height and dampener adjustable coil overs

3. Turbo smart plum back BOV

4. And finally a fully sick POD filter lol

The car is being sold as it is no longer required as i bought a more reasonable daily that can tow and be banged around more with transporting tools and ect. The car is located in Newcastle call me on 0434108477 or email me hear for more info

http://img294.imageshack.us/img294/158/photo088x.jpg

http://img534.imageshack.us/img534/4923/photo089m.jpg

Link to comment
https://www.sau.com.au/forums/topic/326029-rb20-manual-r32-4-door/
Share on other sites

No thanks mate i am after cash to put turbos on my gtr and i already have another car as a daily i really dont need 2 toy cars why dont you keep your 180 they are cheap enough to run if you don't flog them and the sr are realible.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...