Jump to content
SAU Community

Grid Ts Dancer 2

poonta

By poonta,
in Engines & Forced Induction

 Share

Recommended Posts

some_cs_student Veteran

some_cs_student

Posted
Posted

http://www.google.com/search?q=Grid+Ts+Dancer

5 results down:

http://www.skylinesaustralia.com/forums/R3...cer-t35275.html

First post:

There are 2 buttons on the controller, a square on/off button (to swtich between the factory auto 4WD and the controller) and a round button that allows selection between 4WD and FR (rear wheel drive)

Search more, post less :)

poonta Newbie

poonta

Posted
  • Author
Posted

Yes i have read that but that is for the older Grid dancer, the new one has 2 square buttons a display and a knob.

Regards!

/Pontus

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

If you google the full and correct title you will get better results (can the supplier not help you?).

Looking at a picture there are two square buttons, a round knob and an LED display. Using only my powers of deduction (!!!) I would guess that one square button turns the unit on and the other square button returns the car to the control of the Attessa computer. Turning the round knob should produce numbers on the LED display ranging fom 0 to 50 indicating that you are locking in that percentage of drive to the front wheels.

Have a play and see if I am right - (I am just guesing here!)

Duncan Grand Master

Duncan

Posted
Posted
If you google the full and correct title you will get better results (can the supplier not help you?).

Looking at a picture there are two square buttons, a round knob and an LED display. Using only my powers of deduction (!!!) I would guess that one square button turns the unit on and the other square button returns the car to the control of the Attessa computer. Turning the round knob should produce numbers on the LED display ranging fom 0 to 50 indicating that you are locking in that percentage of drive to the front wheels.

Have a play and see if I am right - (I am just guesing here!)

also guessing....but I reckon that is all right except the bold bit. Unless it replaces the factory attessa controller it can only "bend" the input signals like everything else, which means it is probably more like "0 to 50 indicating how much more front drive you are getting than normal" as opposed to a fixed %

I saw claims on the interweb that it creates fixed front torque, but that is not possible with the factory attessa computer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      Just cut the bottom of the guard out. It's no longer got a big duct, to a sealed box, or a restriction. It has all the cold air from outside. Also, that cai you showed looks terrible. Bends are NOT good for go gos!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Like I said, "black magic" LOL In the end,  it is what it is, and hopefully, what this here knuckle head has done is an improvement and not a hindrance Not that I actually notice any negatives now, or that I will get any seat of the pants benefits when all is said and done, but best practice says I shouldn't be pulling intake air from the hot engine bay  Famous last words: I cannot see it being any worse than what it is at the moment 🤔
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      If the gases flowing in those two tracts had the same properties, you could maybe use such broscience. But the exhaust has a different composition, different normal density, different actual density (because of different normal density, and mostly because of the massively higher temperature), and different viscosity (again because of much higher temperature). Consequently, all of the fluid dynamics parameters that matter, that you calculate from these inputs, such as the Reynolds number, friction factors (for wall friction) and so on, are all incomparable.
    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      And we shall have to presume that Canada is the same?
    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      In the US almost everything is E10. It can't exceed 10% by much or fuel systems have trouble adapting. At the same time because MTBE, MMT, and TEL are all banned they need as much ethanol in it as possible to boost octane.
×
×
  • Create New...