Jump to content
SAU Community

Recommended Posts

After selling my skyline and then my S13 silvia to improve finances to buy a house I started missing the fun of driving a RWD sporty car. My daily 626 wagon just wasn't cutting it :)

My budget was minimal as most of my income was/is going on the house, so I looked around for something cheap, but could be upgraded as funds allowed. The S12 Silvia (Gazelle here in Aus) seemed like a good candidate as quite a few S13 parts could be made to work.

I looked for an S12 for a while, but basically gave up when I didn't find anything that interested me. Out of the blue someone I'd contacted earlier messaged me asking if I was still looking and $500 later the notch (notchback) was mine.

The plans for the notch is to gradually improve it, first getting it registered, and then slowly making it more track oriented. It's in pretty good condition due to be made roadworthy and then garaged for 5 years.

Picked up the first parts, grabbing a couple of door pins from centre rd wreckers. R31 door pins are the same as the S12, woo. Hopefully the next lot of parts will be a bit more performance oriented.

S12_Start1.JPG

S12_Start2.JPG

While the next engine hasn't been decided yet, it definitely won't be staying as it is.

CA20E Twin Sparkness

S12_Engine.jpg

But an SR20DE is a definite possibility, with a friend giving me these for free!

S12_Quads.jpg

Link to comment
https://www.sau.com.au/forums/topic/326117-s12-silvia-gazelle-build/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...