Jump to content
SAU Community

Recommended Posts

Hey guys i was at the driving sports event having a go a drifting last night and all went well but i now have 2 problems.

its an R33 RB25det

I fitted a 52mm alloy radiator and wasnt having an issue with cooling then i noticed it to get a little higher on the temp gauge then the previous runs so i did some grip laps and went in when i got back the front thermo has picked up somthing and jamed it and its stuffed.

same time my fuel guage rose and started to read full.... and pretty sure it dosent make its own fuel so i think somthing is broking or stuck

question

1. i bought a new thermo fan as i dont have a clutch fan (had a crack) 16" davies craig can i use the temp switch that the front thermo ran off or should i put a different one in? and run both off that?

2. what do i look for with the fuel gauge so it reads properly agian?

Thanks guys :)

Edited by lookingforboost
Link to comment
https://www.sau.com.au/forums/topic/326444-cooling-and-fuel-guage-failure/
Share on other sites

correct me if im wrong, but the front thermo is almost a meltdown mode fan, kicks in at approx 103 degrees, ive never heard mine going in the 5 years ive had my 32.

many think its an a/c condensor which it isnt either.

maybe go back to clutch fan, no thermo can flow as much as that thing. :)

correct me if im wrong, but the front thermo is almost a meltdown mode fan, kicks in at approx 103 degrees, ive never heard mine going in the 5 years ive had my 32.

many think its an a/c condensor which it isnt either.

maybe go back to clutch fan, no thermo can flow as much as that thing. :)

Thermostat = swap to nismo or other recomended brand, but also run a larger diamater water pump pully to reduce air crevation.

i was thinking of going back to a clutch fan but they are hard to get in good nick and nissan want a million dollars for one, and i dont know if it will fit with the new radiator :(

Will the Nismo thermostat make a difference? i didnt replace it (just did timing belt and water pump)

If i use the 16" thermo fan what temp do you guys think the switch should be? what is the normal operating temp?

Ryan, I have a similar thing with the fuel gauge in my 32. Absolutely NFI what is causing it, but I know it eventually goes back to reading correctly (then "making fuel" again). I say just put up with it.

leave the thermostat as is

long story, but sometimes fitting a higher temp thermostat can help an overheating engine :( seriously

pretty sure u can fit a VL viscous coupling and fan without any issues(burson), yes Nissan viscous coupling was outrageously expensive when i inquired.

Fuel gauge issue is new to me, sounds like a sender unit problem i guess, pull it out of the tank and try moving it by hand, see what it does then.

If it is just the fan that has cracked get a replacement and bolt it on the the fan coupling. Not that expensive. The clutch fan gives you the best cooling of the lot and is much more efficient than the thermo fans. To get good thermo fans that move as much air as the clutch fan will cost you a lot more.

I got a replacement from RHD japan. Nissan should be able to get the same thing out here.

OEM cooling fan

If the coupling is stuffed you can get that from them too

OEM fan coupling

so dont worry about fitting a nismo thermostat? not worth the money?

i'll see it there is enough room with the new radiator if there isnt do you think that the 16" davies will be enough? and what temp should i cut it in at?

Yeah the fuel guage just went up after a lap i spun out on, what dose the sender look like i havnt seen one before but i have changed the fuel pump so i know what to do as far as that, i hope it dosent stay like that forever!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...