Jump to content
SAU Community

Cooling And Fuel Guage Failure :(

lookingforboost
 Share

Recommended Posts

lookingforboost Community Regular

lookingforboost

Posted
Posted (edited)

Hey guys i was at the driving sports event having a go a drifting last night and all went well but i now have 2 problems.

its an R33 RB25det

I fitted a 52mm alloy radiator and wasnt having an issue with cooling then i noticed it to get a little higher on the temp gauge then the previous runs so i did some grip laps and went in when i got back the front thermo has picked up somthing and jamed it and its stuffed.

same time my fuel guage rose and started to read full.... and pretty sure it dosent make its own fuel so i think somthing is broking or stuck

question

1. i bought a new thermo fan as i dont have a clutch fan (had a crack) 16" davies craig can i use the temp switch that the front thermo ran off or should i put a different one in? and run both off that?

2. what do i look for with the fuel gauge so it reads properly agian?

Thanks guys :)

Edited by lookingforboost
Link to comment
https://www.sau.com.au/forums/topic/326444-cooling-and-fuel-guage-failure/
Share on other sites
lotsalag Contributor

lotsalag

Posted
Posted

correct me if im wrong, but the front thermo is almost a meltdown mode fan, kicks in at approx 103 degrees, ive never heard mine going in the 5 years ive had my 32.

many think its an a/c condensor which it isnt either.

maybe go back to clutch fan, no thermo can flow as much as that thing. :)

racer98 Community Regular

racer98

Posted
Posted
correct me if im wrong, but the front thermo is almost a meltdown mode fan, kicks in at approx 103 degrees, ive never heard mine going in the 5 years ive had my 32.

many think its an a/c condensor which it isnt either.

maybe go back to clutch fan, no thermo can flow as much as that thing. :)

Thermostat = swap to nismo or other recomended brand, but also run a larger diamater water pump pully to reduce air crevation.

lookingforboost Community Regular

lookingforboost

Posted
  • Author
Posted

i was thinking of going back to a clutch fan but they are hard to get in good nick and nissan want a million dollars for one, and i dont know if it will fit with the new radiator :(

Will the Nismo thermostat make a difference? i didnt replace it (just did timing belt and water pump)

If i use the 16" thermo fan what temp do you guys think the switch should be? what is the normal operating temp?

blind_elk Grand Master

blind_elk

Posted
Posted

Ryan, I have a similar thing with the fuel gauge in my 32. Absolutely NFI what is causing it, but I know it eventually goes back to reading correctly (then "making fuel" again). I say just put up with it.

lotsalag Contributor

lotsalag

Posted
Posted

leave the thermostat as is

long story, but sometimes fitting a higher temp thermostat can help an overheating engine :( seriously

pretty sure u can fit a VL viscous coupling and fan without any issues(burson), yes Nissan viscous coupling was outrageously expensive when i inquired.

Fuel gauge issue is new to me, sounds like a sender unit problem i guess, pull it out of the tank and try moving it by hand, see what it does then.

Deano45 Rising Star

Deano45

Posted
Posted

If it is just the fan that has cracked get a replacement and bolt it on the the fan coupling. Not that expensive. The clutch fan gives you the best cooling of the lot and is much more efficient than the thermo fans. To get good thermo fans that move as much air as the clutch fan will cost you a lot more.

I got a replacement from RHD japan. Nissan should be able to get the same thing out here.

OEM cooling fan

If the coupling is stuffed you can get that from them too

OEM fan coupling

lookingforboost Community Regular

lookingforboost

Posted
  • Author
Posted

so dont worry about fitting a nismo thermostat? not worth the money?

i'll see it there is enough room with the new radiator if there isnt do you think that the 16" davies will be enough? and what temp should i cut it in at?

Yeah the fuel guage just went up after a lap i spun out on, what dose the sender look like i havnt seen one before but i have changed the fuel pump so i know what to do as far as that, i hope it dosent stay like that forever!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • Duncan
      R34 Handbrake light saying ON and intermittently flashing

      By Duncan · Posted

      ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...