Jump to content
SAU Community

Recommended Posts

ok so last week i decided to wire up my amp and sub.

so i setup the sub without a problem

last night i decided to wire my front speakers (and tweeters) to my amp

so i cut the wire under the dash as it came out of the back of the head unit, so now i had a wire going to each speaker.

so i soldered new wires to them and run it to the boot, plugged it into the amp and .... nothing from the front ...

i just dont see how ive messed it up ... so i decided to turn to the trustworthy people of SAU :(

any ideas

Link to comment
https://www.sau.com.au/forums/topic/326466-front-door-speakers-not-working/
Share on other sites

ok so last week i decided to wire up my amp and sub.

so i setup the sub without a problem

last night i decided to wire my front speakers (and tweeters) to my amp

so i cut the wire under the dash as it came out of the back of the head unit, so now i had a wire going to each speaker.

so i soldered new wires to them and run it to the boot, plugged it into the amp and .... nothing from the front ...

i just dont see how ive messed it up ... so i decided to turn to the trustworthy people of SAU ;)

any ideas

fader from front to rear ? faded to the back not front

wrong wires used?

factory amps? bypass ?

bad crossover wires ?

bad RCA or high level signals

swap the RCA from the sub to the front inputs and see if you have a signal, but be sure to shut off the deck sub out... if it has a crossover built in.

and dont crank it up you just want a sound from them.

could be a lot of things

have you tried to "pop" the speakers from the amp to the doors with a 1.5 volt battery ?, amp not connected?

even with a crossover they will pop when you hit a battery to the wires, with a crossover once the capacitor charges you need to short it out to hear the pop again. PM me for exact details if you don't understand . try not to use anything more then 1.5 volt battery. or it could damage the speakers

I'm assuming your positive you have front speakers in the car ? I've heard that one before.. and found they didn't have any installed..lol

worked it out

my head unit has 'restrictions' on output

would only allow the back to go through the amp enless it was in multifunction mode (only Cds) .... soo i bought a spliter and split the back output and connected the rcas to it and it sounds great

now i have another problem .... my tweeters have a static sound in them when music is played and as i rev the car you can hear the alternator whining -.-

i checked the wires and they dont seem to be over any power cords ..

any ideas ?

You have a ground loop.

Check your amp grounding (especially is it adequate in size, and connected to the body properly).

You running the RCA and power cabling down seperate sides of the car too, right?

Not always the case, if your crossover on the tweeters is too close to a power wire it's picking up A/C ripple.

alternators produce A/C before converting it to D/C a bad alternator can cause it as well

put your ear near other speakers ,does the noise come from all the speakers or just tweets? makes a difference in the fix

the splitter you put in can cause it as well. amp grounds, battery connections dirty, bad engine grounds, computer to close to RCA,the list is huge

some easy reading for you on noise

Noise prevention

and on power in a car

Alternators,batteries, etc

and a site from the GOD of noise reduction, David Navone, I have his big book but you can find it here

Tech Briefs

cheers for the help

i moved my ground wire and now the alternator noise is gone

buttt

still get the static buzz in only the tweeters .... tempting just to unplug the tweeter XD

butt

ill just have to take it all apart and either start from scratch or just try and correct anything thats wrong ...

thanks guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's not any meta data. They have scraped images from everywhere, and then use AI to compare your photo to other photos and work out where you are.
    • I just looked at my camera phone settings, apparently I have "not allowed" for location  Will that stop that app?
    • Can you not just turn it off on your phone if required? I remember a brief on this, well, I remember the brief, not what to actually do. LOL
    • Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
×
×
  • Create New...