Jump to content
SAU Community

Question On The Rb26 Oil Pump Collar

Niswow

By Niswow,
in Engines & Forced Induction

 Share

Recommended Posts

Niswow Contributor

Niswow

Posted
Posted

Hello Everyone

I'm in the middle of rebuilding my motor and i have come accross that my crankshaft on the rb has the short oil drive. My question is if I was to have the oil pump collar put on my crankshaft, would the crankshaft need to be balance after fitting the collar in? The only reason why I'm asking machine shops

were I live don't have the equipment to balance the crank.

Thank You.

  • 4 weeks later...
R31Nismoid Grand Master

R31Nismoid

Posted
Posted
Thank you for everyones comments,and now thats been said.

Can some direct me to a shop in australia, that can install a collar and balance my crank.

Thanks.

The same person doing the rest of your balancing/machining.

v1ncint2 Newbie

v1ncint2

Posted
Posted
Hello Everyone

I'm in the middle of rebuilding my motor and i have come accross that my crankshaft on the rb has the short oil drive. My question is if I was to have the oil pump collar put on my crankshaft, would the crankshaft need to be balance after fitting the collar in? The only reason why I'm asking machine shops

were I live don't have the equipment to balance the crank.

Thank You.

as a engine reconditioner and a x balancer.. rb engines dont need to be balanced as they where only a few grams out say 3 front and 3 rear and a pen weights about 10 grams so u know where im going.. anyway the crank will need to be machined to fit the coller and is used on rb30s and early rb2s as they didnt get enough oil for the needs.. the rb25 has the oil pump drive built up and the rb20s dontmake the power for the oil problem unless drifting.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...