Jump to content
SAU Community

[nsw] Garrett Gt35r Setup And Rb25 Cams

Cro_boy_Mario
 Share

Recommended Posts

Cro_boy_Mario Experienced

Cro_boy_Mario

Posted
Posted

hey all got these for sale, have been laying around for a while since i took it all out of my car

Garrett GT3540 setup for Rb20/25

Includes Genuine garret 3540, Manifold which has been HPC Coated, Matching dump pipe which has a plumback for the wastegate and JJR 38mm gate

Turbo is in perfect condition, .70 Front .63 rear housing

Wastegate was rebuilt before and has a 10psi spring

Only selling as its been off the car for almost 12 months and just lays around collects dust

only requires gaskets, oil and water lines and bolts

$1200 will not seperate unless i have buyers for all

Camshafts for Rb25 with VCT ONLY

they were measured to be 256 degrees, there definately bigger then stock, not sure on lift

$400 for both

Feel free to pm, email for any info

Located in SYDNEY

NO TIMEWASTERS

post-24610-1277798474_thumb.jpg

post-24610-1277798525_thumb.jpg

post-24610-1277798564_thumb.jpg

post-24610-1277798615_thumb.jpg

post-24610-1277798673_thumb.jpg

post-24610-1277798845_thumb.jpg

post-24610-1277798878_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...