Jump to content
SAU Community

Fs Polished Rb26 Rocker Covers

ajohnston
 Share

Recommended Posts

ajohnston Enthusiast

ajohnston

Posted
Posted

changing my polished covers to some candy red ones and i dont want them laying round they are in good nick but will need a good clean before being fitted and have a couple of small scratches that need a polish but apart from that are perfect this is the complete set including cam and coil cover after $450 no offers im happy to post anywhere at a decent cost pm or email me [email protected]

Link to comment
https://www.sau.com.au/forums/topic/326846-fs-polished-rb26-rocker-covers/
Share on other sites
  • 3 weeks later...
  • 4 weeks later...
  • 1 month later...
R31Nismoid Grand Master

R31Nismoid

Posted
Posted
i have tried to contact blitz and r31nismoid but no reply from both of them they dont care not there money ill probably get banned for writing this

That's because it's being dealt with - sorry i thought you were the same person as I've had a few people PM me about this.

Hard to keep track when there is 20 PM's a day coming in mate.

End of the day - it's buyer beware.

You need to contact the Police in your local state, and go from there. There is not a lot SAU can do.

I have shot this user a PM, but clearly if he had dodged you - there is little we can do about it mate.

You should not have blindly EFT'd money across the internet.

PM me all the info you have, i will add him to the bad trader listing.

That's all we can offer here.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...