Jump to content
SAU Community

Recommended Posts

Ok folks, I have an r33 gts-t.

Current exhaust mods are:

- Bellmouth 3inch dump/front pipe

- Xforce 3 inch cat (apparently, came with car)

- 3 inch stainless mandral bent system which also came with car. (it is jasma approved, so its quiet, one huge muffler at the rear that goes 3inch in then splits into two pipes inside and then back out with a single 3inch again, middle muffler is same brand but smaller about the size of a shoe box)

the mufflers appear so say K&H on them, never heard of them?

The car flows great, good performance, cant complain but its too quiet!

It literally makes almost no noise. It is completely drained out by the induction noise.

RB25s have a good note and I would like to get some of that without being too loud and offensive obviously.

Recommendations for a good sensible note? remove rear muffler for a cannon? different rear muffler, no rear muffler etc?

thanks

Link to comment
https://www.sau.com.au/forums/topic/328870-exhaust-modification/
Share on other sites

i would but its all welded, beautiful system. It was a novelty to have it that quiet but truly it makes no noise, no different to stock system. I was thinking have the rear muffler changed to the flange (half way between middle and rear muffler) so I can change back if needed?

Not looking for police attention just a nice, crisp but still reasonably quiet exhaust note

Edited by TUF250
i would but its all welded, beautiful system. It was a novelty to have it that quiet but truly it makes no noise, no different to stock system. I was thinking have the rear muffler changed to the flange (half way between middle and rear muffler) so I can change back if needed?

Not looking for police attention just a nice, crisp but still reasonably quiet exhaust note

i have a jasma fujutsubu canon and just a hotdog in my 3.5inch system, and its as loud as it can get before going over the allowed db, im getting a 3 inch bellmouth and highflow cat (i have stock dump/front and cat) so it will louden it up a bit! cos im after a bit more noise to, so to answer your question, since u have a similar system to mine, i think taking out the center muffler and get a hotdog (if you dont already have one) should make it sound nice.

i would but its all welded, beautiful system. It was a novelty to have it that quiet but truly it makes no noise, no different to stock system. I was thinking have the rear muffler changed to the flange (half way between middle and rear muffler) so I can change back if needed?

Not looking for police attention just a nice, crisp but still reasonably quiet exhaust note

Just get the centre muffler cut out and a straight piece welded in.

Ok sounds good. Would be cheapish too. What about this rear muffler, would it be restrictive? the 3inch in 3inch out but with the twin pipes running through it? its a huge muffler. ill try get a pic. doing the centre would be cheaper than the rear (less bends) Also I could keep my current tip which I dont mind

check out my for sale thread (in sig) for my old exhaust. unique and mildly sounding. :D enough of the sales pitch.

i got a custom 3 inch made up with a straight through muffler and thats it. same sort of sound from my old one just deeper and louder. when it opens up ~4500+ it really starts to roar. i frukin love it... my petrol seems to be draining somewhere.... ;)

Edited by SLY-25T

run a decat, will be slightly louder and slightly faster, best of both worlds!

pros.

more power

more response

louder

their cheap, sell ur current high flow cat and ur infront!

ur system sounds like a quality system, this way u dont have to modify it and f**k with anything

cons.

the environment (f**k the environment)

Edited by jimmys-33T
has anyone got a 3 inch system with a high flow cat and only one big muffler, what did you think if so?

3 inch dump pipe high flow cat and lukey turbo muffler 3in 3 out. no police attention but loud enough and seems to flow enough

run a decat, will be slightly louder and slightly faster, best of both worlds!

pros.

more power

more response

louder

their cheap, sell ur current high flow cat and ur infront!

ur system sounds like a quality system, this way u dont have to modify it and f**k with anything

cons.

the environment (f**k the environment)

CONS! the $$$$$$$$$$ Worth of Ass Raping you will receive if you get caught.

yeah wont be getting a de-cat.

I wonder if just removing the centre muffler and replacing with a straight pipe would sound good? The rear muffler looks quite big and has a twin chamber type design. K&H brand. Might be a good way to go, wont cost much either i figure. thoughts?

im in vic nismoid. I wonder if just removing the centre muffler and replacing with a straight pipe would sound good? The rear muffler looks quite big and has a twin chamber type design. K&H brand. Might be a good way to go, wont cost much either i figure. thoughts?

IMO then you are very silly to change it.

If it's quiet now, then its probably only just legal.

Changing it wil mean you are then over the dB limit almost certainly - I'm yet to see a single muffler system pass.

So you'll end up having to change back for EPA defect reasons anyway.

Stealth & silent is the new black in Vic, it's sadly the only way you can enjoy a Import with relatively low hassle.

Having it loud just simply is not worth the heartache, anyone who's battled the EPA for years (like myself), would most likely agree.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...