Jump to content
SAU Community

Recommended Posts

$500 and they are yours. They are paid for through to 1st April 2011.

Stored at RTA Newcastle. Transfer to your name is as easy as filling out one form together with me and you paying a $175 transfer fee to get them in your name.

They are silver on Black but once they are in your name you can re-design to whatever colour you want.

Cheers

post-43290-1279262384_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/329176-r34gtr-number-plates-500/
Share on other sites

haha havent been on here for ages and your ugly mug...err...screen name comes up...

reckon they'd look good on the pimp mobile?? doubt it.. but it would make some people angry.. mwhaha..

$500 is an absolute bargain!!

hope they get snapped up soon.

cheerio.

Haven't I seen these before somewhere? :P

hey mate, car is top notch, not a scratch, have put some V Spec II aluminium pedals in and thats all.

Hope all is well

Best plates, they'll go at this price.

Bondy

  • 2 weeks later...
  • 4 weeks later...
  • 4 weeks later...

Pity there not S.A plates , i would buy these straight away .

Damn it are people that hard up , they cant afford these plates in NSW

Espescially R34 drivers pull your finger out !!!!!!!

  • 3 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...