Jump to content
SAU Community

Recommended Posts

Hi, I have two sets of GTC wheels for sale. email [email protected]

Location: Melbourne. prefer pickup but can arrange freight at buyers cost.

1st set

18x10 +15 all round, FACE-2 type, carbon center caps, wheel nuts,

will clear big brembo's and 6pot alcon brakes. RAYS don't make these offsets with big caliper clearance anymore. $3200. no offers. (pics below)

154152_2010051657.jpg

154152_2010051640.jpg

IMG_8808-z.JPG

2nd set

18x9 +29, 18x10 +38, carbon center caps, FACE-2 low disk type,

two wheels have some gutter rash and slight dent on the outer rim edge (see pics attached). wheels are not buckled. $2500.

(pics below, wheels are a bit dirty, need to clean with warm soapy water)

post-10650-1279500387_thumb.jpg

post-10650-1279500396_thumb.jpg

post-10650-1279500409_thumb.jpg

post-10650-1279500433_thumb.jpg

post-10650-1279500451_thumb.jpg

post-10650-1279500476_thumb.jpg

post-10650-1279500492_thumb.jpg

post-10650-1279500498_thumb.jpg

post-10650-1279500504_thumb.jpg

post-10650-1279500510_thumb.jpg

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

sorry to jump in on ur thread but i have no idea how these havnt sold yet its been ages.

big bump gl with the sale

also where did u get ur spoiler from that is on ur r34

thanks

julz

price drop for GTC's 18x10, 18x9 - $2350 (pics in first post, above)

price for the other set 18x10 +15 all round is firm at $3200 (pic below)

pickup in melbourne preferred, or can organise freight to east cost for $70-$80.

email [email protected]

159952_2010081206.jpg

hi mate i was after set of these wheels 18x10, 18x9

i well offer you 1800 with no disrespect becuase the tyre point is selling 19x9.5 and 10.5 for 2800 with tyres used as well thanks

price drop for GTC's 18x10, 18x9 - $2350 (pics in first post, above)

price for the other set 18x10 +15 all round is firm at $3200 (pic below)

pickup in melbourne preferred, or can organise freight to east cost for $70-$80.

email [email protected]

159952_2010081206.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Let large companies that are making money off selling kits do the preliminary engineering for you. If they all do -10, then that is all you'll ever need. 
    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
×
×
  • Create New...