Jump to content
SAU Community

Gtr Parts...melbourne..

ChakGTR
 Share

Recommended Posts

ChakGTR Enthusiast

ChakGTR

Posted
Posted

BRAND NEW.. Blitz active twin plate clutch for R32 GTR (Pull type).The BLITZ Active Clutch was designed to hold maximum horsepower while retaining daily drivability. Weights 15-20% lighter than stock. Cost $2200. Selling for $1600 ono.

GARRETT 2860'7 Used for few thousand Km's. Great nik. $1700.

Nismo Le Mans Group A turbos RR581's.60/48. Smaller exhaust side for quik spool up. Rebuilt and havn't been used. Look new. Rare turbos..$1500.

BRAND NEW.. Blitz 700CC injectors. Still in there sealed plastic and boxes. These retail for $1100 at nengun. Fit straight in to RB26. Selling for only $700. This is for all 6 of them.

HPI dumps. 3 inch. These are stainless steel and will last forever. Similar to tomei dumps. Retail for over $1K. Selling used but great nik $550.

Apexi Power FC. Used but good nik. Comes with hand controller $700.

GTR torque split converter. Turn ur GTR from 2wd to full 4wd with the flick of the dial. Retail for $230. BRAND NEW. $150.

Sard fuel pressure regulator. Used but great nik $90.

post-64043-1280070338_thumb.jpg

post-64043-1280070382_thumb.jpg

post-64043-1280070431_thumb.jpg

post-64043-1280070478_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/330338-gtr-partsmelbourne/
Share on other sites
Hiroshima Screamer Grand Master

Hiroshima Screamer

Posted
Posted (edited)

willing to COD the SARD reg to sydney? if so ill take it... if i end up getting it might take the dumps off you aswell.

Edited by Hiroshima Screamer
hudaz Enthusiast

hudaz

Posted
Posted

GARRETT 2860'7 Used for few thousand Km's. Great nik. $1700.

Nismo Le Mans Group A turbos RR581's.60/48. Smaller exhaust side for quik spool up. Rebuilt and havn't been used. Look new. Rare turbos..$1500.

more info please which is better bigger and straight fit ? how much kw ruffly a stock engine with power fc can it push

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...