Jump to content
SAU Community

Recommended Posts

Hey guys im new to skylines australia and I know this topic has been touched many times however I havent been able to solve my problem so any advise would be much appretiated.

I have a r33 which has a ecu modifyed by sam at dr drift so the afm is located between the intercooler and the inlet plenum anyhow I have had a lot of problems with the intercooler pipe blowing off at the afm (which I think is where my problem first started) so I welded a couple of tabs on each pipe and ran a bolt on bar beside the afm to stop it from seperating, once all that was done the car now seems to have a misfire mabe? it runs a little rougher than normal at idle but seems fine to drive untill you hit boost where it coughs an splutters etc on occiasion it will boost in second gear but it over boosts.

I think the fuel pump is fine as its new and it pumps a bit of black smoke out the back while its playing up and also I have tryed a bunch of things to rectify the problem which includes- cleaning fuel filter etc, carn't find any vacume leaks, new spark plugs, pulled the coil packs off my rb26 and tryed them ( splitfires where on the car), inspected the coil harness and added an extra earth, cleaned earth's on motor, tryed a second ignitor,afm & tps, the wastegate was sticking a bit also but have since cleaned around the valve and flange so it now moves freely, I also hooked it up to the consult cable and it shows no erra's though the tps ( first one) was running at .80 volts so adjusted that to 0.45 v.

So as you can see ive had enough of this f**in pice of sh**t so if anyone can help me out here it would make my day.

Link to comment
https://www.sau.com.au/forums/topic/330936-rb25det-misfire/
Share on other sites

check the AFM value during driving on consult

because its been blowing the pipe off you may have physicall damaged the hotwire, its a simple wire after all

Will do mate, when I take a look at the car next its on its second afm though which im pretty confident is in good working order, its gota be somthing like that ive over looked.

Link to comment
https://www.sau.com.au/forums/topic/330936-rb25det-misfire/#findComment-5376204
Share on other sites

Hey guys just thought id run some thoughts past ya,

When the car does boost I carn't hear the wastegate so much yet the boost guage say's the inlet manifold is seeing 22psi which it should be 18psi the wastegate has a 15psi spring in it which leads me to beleve this could a plenum leak, I had allready checked for this but only visualy inspected pipes/hoses etc so are there any suggestions for like a leak down test or something effective without striping everything down?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/330936-rb25det-misfire/#findComment-5378122
Share on other sites

Might have a look at the car this weekend I also noticed it has a slight manifold leak though I wouldn't think it could cause the car to play up this much could it? the engine also seems to be going through huge amounts of fuel is well so im still a bit confused as to what the problem might be?

so come on fella's the more infomation I can get the better im sure some one has had similar symptons any input is always appretiated cheers.

Link to comment
https://www.sau.com.au/forums/topic/330936-rb25det-misfire/#findComment-5382979
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...