Jump to content
SAU Community

What Do I Need To Re Solder

Blazk

By Blazk,
in General Maintenance

 Share

Recommended Posts

t_revz Grand Master

t_revz

Posted
Posted

soldering iron and solder obviously. scratch as much of that crap of and clean it up before starting. try to get the joints hot quickly and either shake it to flick out old solder or just add to it depending on what it looks like. try not to get too hot as diodes and other components will break down and fail. sharp knife or scewdriver when you finish and scratch a line between the tracks on the board incase any residue has settled between them. goodluck

jrm Veteran

jrm

Posted
Posted

The three main bits with the orange around them are the usual culprits for dry joints - you shouldn't even need more solder - just clean up the gunk, then heat them up with an iron to re-flow, and should be good. The orange is a good indicator of an issue with the joint. I re-flowed those three joints on mine (only ones showing issues) when the gauge was starting to play up on occasion (usually going over bumps), and it's been perfect since.

If you see any others that look dry - might be worth cleaning up & re-flowing those too.

jrm Veteran

jrm

Posted
Posted

Is the hose still intact from the plenum? One of the times my gauge failed, I found the hosing split to pieces, barely noticeable - but it just sat on 0 (or just off). I think they fall to pieces after a few years in a hot engine bay - it was terribly brittle.

Blazk Experienced

Blazk

Posted
  • Author
Posted (edited)

I pulled it off the sensor and started up, the suction was defiantly there, didnt see any cracks or splits...but will mulit check it.

Edit: Hose is clean and not cracks or holes that i could see..

Does it matter if i have an after market boost gauge on / will that effect if the stock boost is working ?

Edited by Blazk
jrm Veteran

jrm

Posted
Posted

Aftermarket gauge will typically be hooked up to a different point, so should be fine. As long as the piping from the plenum is going into the boost sensor, and the sensor is plugged in fine, should be good. You could also try reading the voltages out of the boost gauge - the R34 service manual lists what voltages associate with what boost levels (will rule out whether it's sensor or gauge failure)

I'd offer to drop past and let you try out my boost sensor, but the front end of my car is in pieces at the moment for fitting FMIC and not sure it's gonna be driving for another week or so... (depends how lazy I am)

Tommy Kaira RL Mentor

Tommy Kaira RL

Posted
Posted

Try borrow a boost sensor some wreckers will let you try to buy. Or you could blow into the sensor with a hose and watch the guage. I had to wiggle the plug on the boost sensor all the time to get it to work until i re soldered. The pins could be dirty where it plugs in. It sounds like its trying to work. The guage wouldnt even move if it wasnt for the sensor sending something.

Blazk Experienced

Blazk

Posted
  • Author
Posted (edited)
Aftermarket gauge will typically be hooked up to a different point, so should be fine. As long as the piping from the plenum is going into the boost sensor, and the sensor is plugged in fine, should be good. You could also try reading the voltages out of the boost gauge - the R34 service manual lists what voltages associate with what boost levels (will rule out whether it's sensor or gauge failure)

I'd offer to drop past and let you try out my boost sensor, but the front end of my car is in pieces at the moment for fitting FMIC and not sure it's gonna be driving for another week or so... (depends how lazy I am)

Thanks for the offer Jenna, I read your FMIC didnt fit which sucks.

I found the after market boost is hooked up via the BOV so that didnt affect it at all. I went to Andrew's (nightcrawler) last night and picked up his spare triple gauge. Put it in and seems to be working, but only quickly tested it. Looking at the back of the Nismo one there are a few orange solders so i will go over them today and see what happens.

As for the sensor anyone know if the r33 and r34 use the same one ? I read on a couple post people using r33 sensors and they seem to work the same, anyone confirm?

Edited by Blazk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Hi from Canada, Both of my calipers are starting to fail. My car is a 2005 M35 Stagea ARX and I can't seem to find any parts or any cross reference caliper that would fit my car. Is there a company or a similar caliper that would fit and I could replace the OEM one. Or if anyone knows where I can find a new OEM. Any help is very appreciated. Let me know!
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • Matt Z
      SAU NSW - Bathurst Run 2025

      By Matt Z · Posted

      🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day   Highway gets as low as 10l/100km on my end so I'm not as worried about it being a mechanical issue. More likely just the tune on the haltech.
×
×
  • Create New...