Jump to content
SAU Community

Recommended Posts

  • Replies 225
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 2 weeks later...
  • 4 months later...

Maybe.

Wanted to ask the guy at the red light but just couldn't quiet get along side him :\

So, in other news:

I got my gearbox out tonight.

! hour 20 mins, including jacking car up, driveshaft, diff, and getting the box on the ground and out from under the car.

As it turns out....there might be nothing wrong at all with the box, the clutch on the other hand, farken LOL.

Heavy wear on the inside of the compound (10mm section on the inside has about 1.0-1.5mm more wear), the compound itself was shithouse...half the clutch just crumbled as soon as I pulled it off, and the flywheel has scorch marks all round.

So....maybe the crunchies was clutch engagement...since the box hasn't even been leaking oil.

Hahahah...ah....ha....eh.....gayest story of my life :(

Just wait for the next HSV they will try and squeze that motor in to keep up with everyone else.

I had something similar with my 1st 180, car wouldnt go into gear one minute, then fine the next, crunch gears etc, thinking its farked. Pulled the box out and all the clutch plate springs fell out.

I didnt install the clutch...I pulled it out of the halfcut, looked at it, still heaps of meat left on it so I just chucked the good gearbox on it and threw it into the Ceffy...Stock clutch, 126xxx kms...dare say it was the factory clutch ?

Doesnt matter, new flywheel and GTR clutch on now....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...