Jump to content
SAU Community

Recommended Posts

I have for sale a RB26DETT Forged Short Motor

Built for big boost and HP by RB specialist Stuart Jones of Cavehill Enignes

NEW

JE custom forged pistons , with contact reduction and double forced gudgeon oiling

Tomei "H" forged conrods , with upgraded ARP 2000 12 point 8740 chrome moly 220000psi bolts

Perfect Seal race set piston rings with gapless 2n/d rings

ACL Race heat treated main and big end bearings

ARP main studs , ARP headstuds

Nissan N1 oil pump

Tomei 1.5mm oil restrictor

NSK timing belt tensioner , NSK timing belt idler

KP gasket set with multi layer steel head gasket (MLS)

Block

Acid dipped , magnaflux cracktested , cylinder bores sonic test for wall thickness ( X-rayed ) ,

Bored .5mm and diamond plateau honed , Decked square to main tunnel

Crankshaft ( late 32 or 33 with long oil pump drive )

Acid dipped , electromax cracktested , measured , linished ( micro polished ) and fully balanced

Engine is assembled to short motor with sump fitted

c/w secondhand

GTR sump complete with 4.111 diff ratio

alloy engine mount brackets , p/s and a/c mounting brackets , oil filter housing , oil cooler and water pipes ,

thermostate housing , harmonic balancer

All it needs is a cylinder head , water pump and a timing belt

Price $ 8800

May trade or swap for BNR32 GTR

Can email or SMS photo's

PM , call or text

0407807195 Stu

hey mate

to get all the testing n maching done to your block

how much did it cost roughly

what are the pros of getting ur block acid dipped, magnaflux cracktested ?

Some more pic's

ARP head std kit , Adjustable cam gears

Oil filter housing , cooler assembly

Harmonic balancer , p/s bkt , a/c bkt , engine mount bkt's

Exhaust manifolds

post-37725-1282218889_thumb.jpg

post-37725-1282218900_thumb.jpg

post-37725-1282218910_thumb.jpg

post-37725-1282218920_thumb.jpg

  • 2 weeks later...

I have had a few PM's about the custom pistons

Contact Reduction Grooves: The purpose of machining these grooves is to reduce the amount of contact area

against the cylinder wall when the piston “rocks over”. Contact reduction also serves to disrupt the flame travel into

the crevice area thus helping to reduce detonation.

Double Pin Oilers: Double Pin Oilers deliver twice the amount of oil to the wrist pin as compared to the standard single pin oiler.

8800. thats abit high dont ya think

considering its a standard block with a n1 oil pump :-S

NEW

JE forged pistons , custom ordered with contact reduction grooves and double forced gudgeon oiling

Tomei "H" beam SNCM439 metal forged conrods

ARP 2000 12 point 8740 chrome moly 220000psi conrod bolts

Perfect Seal race set piston rings with gapless 2n/d rings

ACL Race heat treated main bearings

ACL Race heat treated big end bearings

ARP main studs

ARP head studs

Nissan N1 oil pump

Tomei 1.5mm oil restrictor

NSK timing belt tensioner

NSK timing belt idler

KP gasket set with multi layer steel head gasket (MLS)

Alloy adjustable cam gears

Add up all these new parts then see if $ 8800 is too high , then add machining costs

Cash talks and im open to offers

Cheers

did ur machining cost 3 grand did it

NEW

$ 3300 JE forged pistons , custom ordered with contact reduction grooves and double forced gudgeon oiling ( purchased Feb/2009 when $1 aud bought .64 cents us)

$ 1544 Tomei "H" beam SNCM439 metal forged conrods

$ 350 ARP 2000 12 point 8740 chrome moly 220000psi conrod bolts

$ 550 Perfect Seal race set piston rings with gapless 2n/d rings

$ 165 ACL Race heat treated main bearings

$ 95 ACL Race heat treated big end bearings

$ 257 ARP main studs

$ 460 ARP head studs

$ 535 Nissan N1 oil pump

$ 22 Tomei 1.5mm oil restrictor

$ 95 NSK timing belt tensioner

$ 115 NSK timing belt idler

$ 550 KP gasket set with multi layer steel head gasket (MLS)

$ 130 Alloy adjustable cam gears

USED

$ 1300 R33 , Late R32 RB26DETT sub assembly suit reco inc diff assembly ( purchased in 2008 )

Just to give you an idea on prices

Cash talks and im open to offers

Cheers

You interested or just wasting his time? :S
no hes not intrested.

His motor is worth 4 to 5 times what this guy is asking !

Thanks Guy's , for your positive inputs

Cheers STU

THE DO'S AND DONT'S OF THE SAU CLASSIFIEDS!

2. No price debates - put simply if you do not agree with the price being asked, do not comment on the thread. If you believe the seller is asking too much then either pm the thread starter or dont buy the items advertised - simple.

There is to be no "My cousin can get it for much less" or "Your asking too much" comments

did ur machining cost 3 grand did it

have u ever built an motor? i got mine back from the machine shop yesterday with a bill of near 3k just for machining/labour..

its also the time and effort to aquire the parts, big fkn headache can take months etc

Edited by Char
have u ever built an motor? i got mine back from the machine shop yesterday with a bill of near 3k just for machining/labour..

its also the time and effort to aquire the parts, big fkn headache can take months etc

too right!!!

dont even start with trying to enplane the headache!

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...