Jump to content
SAU Community

Recommended Posts

hey guys and gals

i am changing over all my studs and replacing the ex manifold gaskets on my rb20.

first thing i am wondering the gasket kit that i got its got both the whole 6 all the together gasket one and also the 6 individal gaskets, which one is better to use???

i am replacing all the studs also since i already had a few broken ones so might as well replace them all. is there anything else i could be doing when fitting up the new ones?

well since i had a few broken studs i am missing a few nuts and washers can i just go to my local hardware store and get like stainless steel nuts and washers??

last thing. the tensions, when i was taking all the turbo, dump, ex manifold i did spray wd40 on all the nuts before taking them off and all, just when i went to take them off there wasnt much effort in taking them off at all, like i didnt have to even crack loose a nut, it was just a lil too easy, soooooo how tight do i really have to do themm upp

thanks

Link to comment
https://www.sau.com.au/forums/topic/333792-gasket-studs-nuts-and-washers/
Share on other sites

dont use a rattle gun, most of that stuff doesnt need to be as tight as you'd think. just nip it up fairly tight with a normal sized ratchet.

nissan want too much for exhaust manifold nuts so i got some from a fixings shop in wangara, cost about $5 for a full set. just take a stud in and get some high tensile nuts in the right thread

little off topic but if you have a spare exhaust manifold gasket i'll buy it off you

Rattle gun won't fit down there easy...infact depending on the manifold, sometimes even a ratchet isnt the go. Need to use uni joint, or a spanner.

As for studs and gaskets. Use Nissan items, they're more expensive, but they're of alot better quality than the other shit.

obviously dont use a rattle gun need ring/open ended spanners 14-15mm depending what nuts you use and socket set with either 14mm or 15mm sockets

i do mine pretty tightish obviously the areas that you cant get a socket to just tight it up as much as you can with the spanner as your restricted for torque and personel preferance i use loctite

can get high tensile nuts from bunnings or just go auto one

yeah nice one there andrew haha. i dont need to know sizes here i have already taken everything off. so do them up pretty tight, guess i would also need to get washers tooo with the high tensile nuts???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...