Jump to content
SAU Community

Overheating Issues...

Medium Dave
 Share

Recommended Posts

Medium Dave Proficient

Medium Dave

Posted
Posted

Hey Guy's, I am throwing myself at your mercy for some assistance with my scoobie - this forum is the only place I know of for decent advice! I have even spoken to mechanics and I am getting nowhere

It started overheating the other week - engine hot, radiator cold. So I replaced the thermostat with a burson unit and stuck the hose in various points (block, heater, radiator and no blockage), no improvement. Then I replaced the waterpump (another burson) and it was good for a week when it started overheating again... it began overheating, then going back to normal temp's, then overheating, then back to normal - so I replaced the thermostat with a gen subaru one, and it was good for one drive for 20 minutes, quick fuel stop then overheated then back to 3/4 hot on the way home. I filled it with some water, seemed to be a bit low, then it guzzled the water, then comes back, and occasionally spits water out. The radiator was hot to touch, but the heater is cold and the thermofans kick in as they should

I am wondering if I scored a dud water pump and I should go to Subaru for a proper one, but I was wondering if anyone had any other ideas before I pull this thing apart again (I am so close to just setting the damn thing on fire...)

Many thanks >_<

Link to comment
https://www.sau.com.au/forums/topic/334004-overheating-issues/
Share on other sites
warps Mentor

warps

Posted
Posted

Stupid question, but are you sure the temp gauge is working properly?

This isn't the only place where you get intelligent responses to questions. You have just been looking in the wrong places. If I ever needed help on a WRX, I think I'd head over to some gravel rally forums. :(

Medium Dave Proficient

Medium Dave

Posted
  • Author
Posted

Cheers Scotty - I will drop into a radiator place on the way home. I admit I did not check the thermostat, from where I live the cost of a replacement was sufficiently low enough that I grabbed one while I was at the service centre when I spoke to one of their mechanics rather than make another trip.

The gauge seems to represent the temperature of the engine when I touch various hoses and parts, so I have no reason to mis-trust it so far, and it is true Warps, there is probably many places I could go to for good info, but I'm a big fan of 'go with what you know' and this forum has not led me astray yet :(

Many thanks guy's

lachlanw Veteran

lachlanw

Posted
Posted

sounds to me like its a big air lock at the top of the drivers side end tank . what year is your car ? does it have a header tank and a line from the top of the drivers side end tank back to the header tank ?

you replaced the radiator . does it have this line ?

what you do is take the little hose (if it has one) or the main radiator hose off the drivers side end tank and get a mate with a rag tied round the hose to jam it in the rad cap and not stop untill yuou have a solid stream of water coming out . do it with the front of the car a shigh as you can get (ramps or a driveway ) and make sure the heater is on full hot

iplen Mentor

iplen

Posted
Posted

on the top left (From the front) there will be a square plug, with a phillips screw fitting in it, car on ramps, heater flat out, open that and start pouring water in keep going until A) the heater is HOT and B) water comes out of the bleed valve. From personal experience (over $6k spent on a NON turbo motor in an 89 liberty) Subarus are very sensetive to air locks, and overheating, would not be surprised if the first time has done a headgasket and that will be the end of it I am afraid. Subaru is the Crazy Japanese Cousin of the Euro car brands. If it has done a headgasket.... I have a motor for sale....

Medium Dave Proficient

Medium Dave

Posted
  • Author
Posted

I'm afraid it's just an old non turbo liberty - and it is now behaving exactly like it was before I replaced the water pump, the only way to make water in the rad move is to squeeze the top radiator hose. I am familiar with the procedure for refilling coolant, and the water is not full of oil and vice versa so hopefully the head gaskets are still intact (mind you it's probably just a matter of time)

I think I will give it to some radiator guy's this afternoon (couldn't make it in yesterday) to see if it's blocked, but I wont be surprised if it's this water pump again...

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...