Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...
  • 1 month later...

20 is out, 26 is upside with sump off and its all ready at the enigineer's

-Modify Sump

-n1 oil pump

-New water pump

-New water pipes

-new gaskets throughout inc inlet, exhaust, rocker covers, front crank seal, rear main etc

-New engine mounts (old ones broke on way out)

-Need either another z32 and a chip so stock ecu runs it ok, or a pair of stock GTR air flow meters till i go aftermarket ECU

-Paint inlet and covers

-New catch can

-Front Pipe

-Modify Cooler Piping

-install twin plate

-New filters

-install motor

-Finish wiring

think thats a pretty small list considering!

  • 4 weeks later...

OK finially some progress and some new pictures, Have sorted out the wiring. and all the plumbing on the 26. god there is alot you dont need!

Aircon compressor removed, rb26 power steering pump removed and the rb20 bolted into place. (conveniently fits using the standard mounting location of the air conditioning compressor)

Front pipe has turned up, still waiting on AFM's and hks hard intake kit. But the thing really slowing me down is the VRS kit, will seriously hurt somebody if this shit doesnt turn up soon! As soon as it gets here the motor will be redy to have clutch bolted on and motor dropped into place.

All the engine covers have been nicely painted aswell. Here is some pics, also one of my new workbench :)

(actually just reallised i didnt take one of the actuall work bench so i will get onto that in the next few days )

P1110903.jpg

P1110904.jpg

P1110906.jpg

P1110909.jpg

Whole front of motor is finished

Cam seals

N1 oil pump

Water pump

crank seal

new idler bearing

new tensioner and spring

Gates timing belt

hmm think thats the whole front? Was starting to get super angry as i realised i got sent 3 crank seals instead of one crank and two cam seals... turns out cam seals are same part number as crank seals in 32 gtr's haha :)

Still waiting on vrs, and waiting for my standard manifolds and dumps to get painted in that black heat proof stuff. Should tidy it up a bit.

Then only thing left is rear main seal and bolt clutch/flywheel up and drop it in

Wiring is allready finished. Then just mod front pipe to fit my existing 3" cat back system and two cooler pipes and bam back on the road :)

Also found out i got a nice surprise turbo wise with my front cut, .60 - .64 turbos, There either N1 or Nismo Group A turbos. Pretty happy bout that

  • 2 weeks later...
  • 1 month later...

Car is finially finished and running, honestly cant stress enough if you want something done right do it your f**king self. only outsourced one part of the build and it put me behind 3 weeks and cost me more money

but 10psi for a week or so, a second oil and filter change. some dyno time to check afrs after that and happy days.

And some new semi slicks tomorrow morning! happy days, words cannot express how it felt to drive it out of the garage for the first time in 4 months!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...