Jump to content
SAU Community

Recommended Posts

hey guys i woke up this morning , and noticed my driver' side mirror was missing.... why would someone just steal that..... its just annoying.

Anyway anyone selling one? or know of a place that sells one i need one asap as i need to drive the car, and also do i just re attactch it with glue?

Link to comment
https://www.sau.com.au/forums/topic/336399-r34-side-mirror-gone/
Share on other sites

Ask in the " wanted to buy thread" and that sucks to have ur mirror missing. what a nuisence.

Does anyone know if i can use a mirror from a r32? because only the glass mirror was missing, and i saw someone stripping a 32 in adelaide. Since no one has got back to my about a 34 mirror.

thanks!

No you cant use the 32 glass. Ring any glazier and they can replace it for you, they might cut it a bit dodgy tho, but i doubt wreckers will just sell you the mirror without trying to offload the whole side mirror.

you can always take the other mirror out, and ask a glazier to put it mirror side-to mirror side and cut around it to make a new piece. it , mathematically, should then fit perfect and look good.

  • 2 weeks later...
hey guys i woke up this morning , and noticed my driver' side mirror was missing.... why would someone just steal that..... its just annoying.

Anyway anyone selling one? or know of a place that sells one i need one asap as i need to drive the car, and also do i just re attactch it with glue?

mate if you can figure out how to get one can you please let me know as well

same thing happened to me the other night

bloody nuisance, what are they going to do with just a mirror (unless they were also missing one and it would make sense)

but yeah good luck finding one aye~

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...