Jump to content
SAU Community

Recommended Posts

For Sale

Skyline R33 series 2

list of mods

18"VR5 mags good bridgestone adrenalins

slotted rotors with blue painted calipers

cusco front strut bar

gtr rear strut bar

non hicas rear cradle

turbotech boost controller

turbosmart plumb back BOV

HKS front mount intercooler

Garret TB3401 big low mount turbo

3" stainless exhaust from turbo back

oil catch can

fuel pressure regulator

mines ECU fuel,boost and speed cut

short throw short shifter

extreme heavy duty clutch

greddy turbo timer

ISC coilovers 2000kms old

body kit

Boost gauge on pillar

oil and water temp and volt gauge in dash

sony stereo with 6x9 explode rear parcel shelf. 6" explode doors and kenwood 12"sub in boot on custom backing

alarm

Very rare factory wood grain dash and gear surround. wooden handbrake lever and gear stick knob. I have never seen this anywhere else

Ive had the car for 5 yrs and serviced every 5000kms

Last time car was on the dyno it was pulling 260rwkw with a stuffed CAS. It would do more than that now.

Its been a great car Im just moving on to better things

Bad points

I think there is a head gasket problem. The radiator overheated once I thought it might of been from the head gasket. I put a bottle of copper liquid in it and it stopped (car still boosts fine but it may need to be looked at in future) and the gearbox has a slight crunch between 1st and 2nd

Im looking at $10000 as is or $12000 with another motor and gearbox as a spare in exellent condition ready to be swapped.

Also has a taller ratio diff gets higher speeds.

If you would like to know more you can PM me or 0427999093

http://i533.photobucket.com/albums/ee334/r...ds/P1050569.jpg

http://i533.photobucket.com/albums/ee334/r...ds/P1050580.jpg

http://i533.photobucket.com/albums/ee334/r...ds/P1050577.jpg

http://i533.photobucket.com/albums/ee334/r...ds/P1050579.jpg

http://i533.photobucket.com/albums/ee334/r...ds/P1050573.jpg

http://i533.photobucket.com/albums/ee334/r...ds/P1050572.jpg

http://i533.photobucket.com/albums/ee334/r...ds/P1050575.jpg

Link to comment
https://www.sau.com.au/forums/topic/336674-skyline-r33-s2/
Share on other sites

This would be a cheap car if someone fixed the head gasket themselves. I can even throw one in the sale. Otherwise if this car goes to the mechanic to get fixed the price will go back up. Car has been going strong still for the last 3 months. runnig 15psi and 260rwkw

Link to comment
https://www.sau.com.au/forums/topic/336674-skyline-r33-s2/#findComment-5478997
Share on other sites

Is there water in the oil?

No water in oil. Stil drives and boosts nicely. ive been now driving it the last 4 months when i first noticed a bit of a problem. And havent had a problem again since I put the coper liquid in radiator. Its supposed to be a permenant fix for head gaskets. Thats what the mechanic suggested

Link to comment
https://www.sau.com.au/forums/topic/336674-skyline-r33-s2/#findComment-5504693
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...